Cisco Systems CIVS-IPC-2630V manual Viewing Video through Third-Party Devices or Software

Page 83

Chapter 4 Viewing Live Video

Viewing Video through Third-Party Devices or Software

Viewing Video through Third-Party Devices or Software

You can allow users to access video streams from the IP camera through third-party mobile devices, or through the VLC media player or equivalent software.

To do so, you must configure the RTSP Port option in the Advanced Setup window. This option enables the IP camera to receive Real-Time Streaming Protocol (RTSP) commands. For more information, see the “Advanced Setup Window” section on page 3-7.

To access a primary H.264 stream, configure Single H.264 Stream, Dual H.264 Streams, or Dual Streams (H.264 + MJPEG) for the Streaming Mode option in the Video window. These settings lets you enable a primary H.264 video stream, which is useful for providing third-party devices. For more information, see the “Video Window” section on page 3-16.

To access a secondary H.264 stream, configure Dual H.264 Streams for the Streaming Mode option in the Video window. This setting lets you enable a secondary H.264 video stream, which is useful for providing third-party devices or software with a video stream that is at a lower resolution than the primary stream. Some software and devices require this lower resolution, which is 352 x 240 for NTSC or 352 x 288 for PAL. For more information, see the “Video Window” section on page 3-16.

To access a primary MPEG-4 stream, configure Single MPEG-4 Stream, Dual MPEG-4 Streams, or Dual Streams (MPEG-4 + MJPEG) for the Streaming Mode option in the Video window. These settings lets you enable a primary MPEG-4 video stream, which is useful for providing third-party devices. For more information, see the “Video Window” section on page 3-16.

To access a secondary MPEG-4 stream, configure Dual MPEG-4 Streams for the Streaming Mode option in the Video window. This setting lets you enable a secondary MPEG-4 video stream, which is useful for providing third-party devices or software with a video stream that is at a lower resolution than the primary stream. Some software and devices require this lower resolution, which is 352 x 240 for NTSC or 352 x 288 for PAL. For more information, see the “Video Window” section on page 3-16.

To access an MJPEG stream, configure Single MJPEG Stream or Dual Streams (MPEG-4 + MJPEG) for the Streaming Mode option in the Video window. This setting lets you enable an MJPEG video stream, which is useful for providing third-party devices. For more information, see the “Video Window” section on page 3-16

This section provides examples for how to access various video streams. For related information, see Cisco Video Surveillance API Reference Guide.

Accessing the Primary H.264 Stream

In the following commands, the ip_address argument represents the IP address of the IP camera. After you enter the command, enter your IP camera user name and password when prompted.

•To access the primary H.264 stream with video and audio, enter this command: rtsp://ip_address/img/h264media.sav

•To access the primary H.264 stream with video only, enter this command: rtsp://ip_address/img/h264video.sav

Accessing Secondary H.264 Stream

In the following commands, the ip_address argument represents the IP address of the IP camera. After you enter the command, enter your IP camera user name and password when prompted.

•To access the secondary H.264 stream with video and audio, enter this command: rtsp://ip_address/img/h264media2.sav

Cisco Video Surveillance 2630 IP Dome User Guide

 

OL-24130-02

4-5

 

 

 

Page 82 Page 84
Image 83
Page 82 Page 84
Contents Americas Headquarters Cisco Video Surveillance 2630 IP Dome User GuideCisco Video Surveillance 2630 IP Dome User Guide Iii N T E N T SSnmp Window Vii OverviewOrganization Viii Features, IP Camera Overview, FeaturesIP Camera Overview Physical Details, Package Contents,Top of the 2630 IP Dome Physical DetailsOverview IP Camera Overview Bottom of the 2630 IP Dome Described in the Resetting the IP Camera section onPackage Contents Before You Begin Getting StartedPreventing Electrostatic Discharge Damage Installing the Cisco Video Surveillance 2630 IP DomePreparing for Installation Passing the Audio Cable through a Ferrite Core Mounting with a Conduit Base ProcedureAttaching the Conduit Base to a Ceiling or Wall Attaching Base Plate to Conduit Base Attaching the Camera to the Base Plate See -1 onCisco Video Surveillance 2630 IP Dome User Guide Attaching the Privacy Shield and Dome Mounting with a PendantOL-24130-02 Pendant Gasket Conduit base 10 Attaching the Base Plate to the Conduit 11 Attaching the Camera to the Base Plate 12 Attaching the Privacy Shield and Dome Performing the Initial Setup of the IP CameraProtocol//ipaddress Http//203.70.212.52 Accessing the IP Camera WindowsHttps//192.168.0.100 Https//203.70.212.521024Http//203.70.212.521024 Adjusting the Video Image13 Adjusting the Camera Lens on the 2630 IP Dome Reset Type Procedure Remarks Powering the IP Camera On or OffResetting the IP Camera Cleaning the IP CameraOL-24130-02 Configuration Overview Configuring and Managing the IP CameraConfiguration Item Explanation Guidelines for Use Reference See the Focus/Zoom Window See the Alarm I/O PortsSee the Audio Window section See the Privacy RegionSnmp Navigating the Configuration WindowsOption Description Setup WindowsBasic Setup Window Device SettingsOption Description Network Settings Advanced Setup WindowBonjour OptionOption Description QoS IP Filter WindowEAP-FAST Options Eapol WindowEAP-TLS Options Users Window Administration WindowsUsers Window, Maintenance Window, Firmware Window, User List AdministratorMaintenance Window Firmware Window Video Window Audio/Video WindowsSettings Dual Streams MPEG-4 + Mjpeg -Configures MPEG-4 forMPEG-4 Settings Resolution Choose the resolution of the Mjpeg video stream Mjpeg SettingsPAL/50 Hz Video AdjustmentDay/Night Vision OptionsOption Description Duplex Talk and Listen Audio WindowControls section on Full Duplex Talk and Listen Privacy Region WindowFocus/Zoom Window Choose Simplex Talk Only , Half Duplex Talk or Listen , orInitialization Window, Complexity Window, Security WindowsInitialization Window Users Window section on Complexity WindowMail/FTP/HTTP Window Applications WindowsSecondary Smtp Server Described in the Basic Setup Window section onMail Setup Primary Smtp ServerHttp Notification Mail BodyPrimary FTP Secondary FTPSystem-provided-name-value-pairs is the event information Motion Detection WindowEvent Window Trigger Event Event ScheduleNew Schedule Clear buttonAttachment Mail/FTP/HTTP Window section onSnmp Window Manual Control Settings Alarm I/O Ports WindowAlarm Input Settings Alarm Output SettingsSystem Status Status WindowsSystem Window Audio/Video Window Audio SettingSyslog & Log Window Network WindowSys Log Server Local LogSystem log messages Log ListMessage Explanation Syslog and Log Information Address FTP log messages Address1 Port1 Address2 Port2 , UserSmtp log messages Video Log WindowDelete All button Delete buttonOL-24130-02 Home Window Overview Viewing Video through the Home Window OverviewHome Window Audio controls Home Window ControlsControl Description Digital zoom controlsFor related information, see the Video Window section on Snapshot controlsSave IP camera controlsViewing Video through Third-Party Devices or Software Accessing the Primary H.264 StreamAccessing Secondary H.264 Stream Accessing Dual Streams H.264 + Mjpeg Accessing the Primary MPEG-4 StreamAccessing Dual MPEG-4 Streams Accessing the Mjpeg StreamAccessing Dual Streams MPEG-4 + Mjpeg OL-24130-02 Troubleshooting Troubleshooting For instructions, see the Video Window section on Using the IP Camera with Cisco VSMOL-24130-02 IN-1 D EIN-2 IN-3 DSCP, for QoS Dual streamingIN-4 SdramIN-5 LEDIN-6 Options OverviewIN-7 IN-8
Top Page Image Contents