Samsung SCC-C6453N user manual Screw Fixing Hole Diagram

Page 11

2.Use the three “SCREWS” to fix the “FRAME SET” on a “CAMERA” installation position.

FRAME SET English SCREW

SCREW

ADAPTOR

SCREW <Fixing Hole Diagram>

3.Connect external cables to the “CONNECTORS(ALARM IN, POWER, RS-485, ALARM OUT)”and connect the “CONNECTOR” to the “ADAPTOR”.

Insert the cable into the “FRAME SET”, and close the “ADAPTOR”.

			FRAME SET
	POWER INPUT ALARM OUT		ADAPTOR
ALARM IN		RS-485
			SNAP FIT
			BNC JACK
			INSULATION TUBE
M	 Then, wrap the “BNC JACK” with the “INSULATION TUBE”, and use an insulation
M	tape to seal up the end of the “INSULATION TUBE” so that the “BNC JACK” does

not protrude outside of the “INSULATION TUBE” coating.

For more information about cable connection, refer to “Connecting the adaptor cable”. (page 19)

English _11

00890A-NA_SCC-C6453N-ENG.indb 11

2009-08-05 오후 3:03:

Image 11

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents What’s Included FeaturesFrame SET At a GlanceCamera Installation Preparing InstallationInsert the cable into the Frame SET, and close the Adaptor Screw Fixing Hole DiagramProtective Tape from on the lens Button Frame SET Cover Camera Use SW606, SW605, and SW604 to specify the camera address Initial SetupCamera Address Setup Communication Protocol SetupFactory default is 9600 BPS Baud Rate SetupSetting RS-422A/RS-485 Termination Use pins #5, #6 of SW603 to set the baud rateSame address in the network RS-422A/RS-485 Full Duplex OrganizationVideo terminal on the rear of monitor BNC Cable Connecting with Other deviceConnecting to a monitor To connect the controller To connect AlarmTo connect Alarm OUT Adaptor Board Connecting the adaptor cablePower Supply Camera will resume the last run operation How to use the keyboard controllerUsing OSD icons Main Menu  ITS ProfileNight  Location Specify the display position of the camera ID You can configure the general settings of the camera moduleCamera SET Camera IDAGC  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a IrisSENS-UP MotionDNR ShutterDAY/NIGHT You can specify a recording mode according to the sceneFlickerless XDRSET-AUTO SET are not available Auto Switch or Auto FocusNeeded White BAL DAY/NIGHT Digital Zoom Zoom SpeedDisplay Zoom Display P/TPOSI/NEGA SyncAGC Color SUP ReverseAdvanced You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily Intelligent VideoDisplay ResolutionAlarm OUT Privacy ZonePreset Select Position and adjust PAN Select the preset numberYou can set the Auto PAN, PATTERN, and Auto Play Auto Pan SetupSettings so define them again after the operation Auto SETPosition Direction Left Endless OFF Speed Select the Start and move the camera using pan/tilt/zoom Pattern SetupScan Setup ~ 511 for Preset Auto Play SetupSelect Main MENU-ZONE SET Zone SETYou can set the north direction and the zone coverage Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETProportional P/T Factory DefaultsPassword OSD ColorSelect Main MENU-SYSTEM Info CommunicationSystem Info You can check the system informationYou can set the language of the user interface LanguageFunction Key Shortcut KeysSpecifications Tilt range -6˚~186˚ Preset Pan Speed 600˚/sec, maximumDescription PAN range 360˚Endless Manual Pan Speed 0.01˚~ 180˚/secProduct Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후