Samsung SCC-C6453N user manual Baud Rate Setup, Setting RS-422A/RS-485 Termination

Page 15

Baud Rate Setup

Use pins #5, #6 of SW603 to set the baud rate.

English

BAUD RATE	PIN 5	PIN 6

4800 BPS	ON	ON

9600 BPS	OFF	ON

19200 BPS	ON	OFF

38400 BPS	OFF	OFF

The factory default is 9600 BPS.

Setting RS-422A/RS-485 Termination

As it is shown in the structure map, when Controller and RS-422A/RS-485 is connected, it should be terminated according to the Cable feature of impedance on the each end of the transmitting line to transfer the signals in long distance by controlling the reflection of the signals to the lowest.

Controller

Termination

n < 32

Termination

TX+(DATA+)

SW1-ON

TX-(DATA-)

RX+

RX+

RX-

RX+

RX-

RX+

RX-

RX-

CAM 1

CAM 2

CAM n-1

CAM n

<RS-485 Half Duplex Organization>

Termination : Using numbers 1 and 2 PIN, turn to <ON> and it will be terminated.

English _15

00890A-NA_SCC-C6453N-ENG.indb 15

2009-08-05 오후 3:03:

Image 15

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents What’s Included FeaturesAt a Glance CameraFrame SET Installation Preparing InstallationInsert the cable into the Frame SET, and close the Adaptor Screw Fixing Hole DiagramProtective Tape from on the lens Button Frame SET Cover Camera Use SW606, SW605, and SW604 to specify the camera address Initial SetupCamera Address Setup Communication Protocol SetupFactory default is 9600 BPS Baud Rate SetupSetting RS-422A/RS-485 Termination Use pins #5, #6 of SW603 to set the baud rateSame address in the network RS-422A/RS-485 Full Duplex OrganizationConnecting with Other device Connecting to a monitorVideo terminal on the rear of monitor BNC Cable To connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu  ITS ProfileNight  Location Specify the display position of the camera ID You can configure the general settings of the camera moduleCamera SET Camera IDAGC  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a IrisSENS-UP MotionDNR ShutterDAY/NIGHT You can specify a recording mode according to the sceneFlickerless XDRAuto Switch or Auto Focus NeededSET-AUTO SET are not available White BAL DAY/NIGHT Digital Zoom Zoom SpeedDisplay Zoom Display P/TPOSI/NEGA SyncAGC Color SUP ReverseAdvanced You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily Intelligent VideoDisplay ResolutionAlarm OUT Privacy ZonePreset Select Position and adjust PAN Select the preset numberYou can set the Auto PAN, PATTERN, and Auto Play Auto Pan SetupSettings so define them again after the operation Auto SETPosition Direction Left Endless OFF Speed Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom ~ 511 for Preset Auto Play SetupZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETProportional P/T Factory DefaultsPassword OSD ColorSelect Main MENU-SYSTEM Info CommunicationSystem Info You can check the system informationYou can set the language of the user interface LanguageFunction Key Shortcut KeysSpecifications Tilt range -6˚~186˚ Preset Pan Speed 600˚/sec, maximumDescription PAN range 360˚Endless Manual Pan Speed 0.01˚~ 180˚/secProduct Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후