Samsung SCC-C6453N user manual Camera SET, Camera ID

Page 24

setup

CAMERA SET

You can configure the general settings of the camera module.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)

1.Select <MAIN MENU> - <CAMERA SET>. The Camera Setup menu appears.

2.Change the settings as necessary, or select an item to check.

CAMERA SET 

CAMERA ID	OFF
IRIS	ALC
MOTION	(F.FAST) ---
DNR	MID
SHUTTER	(OFF) ---
SENS-UP	AUTO X4
FLICKERLESS	OFF
XDR	MID

CAMERA ID

Provide the ID and location for a camera that displays on the screen.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)

1.Select <CAMERA SET> - <CAMERA ID>.

2.Use the joystick to select a desired character, then press [ENTER].

In the lower input box of the screen, the selected character will be entered.

You can enter up to 54 characters including alphabets, numbers and special characters.

LOCATION : Specify the display position of the camera ID.

CAMERA ID

ABCDEFGHIJKLMNOPQRSTUVWXYZO 123456789 : ?_+()/

SP SP LOCATION

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

3.When done, press [ENTER].

The camera ID will be displayed in the specified position.

24_ setup

00890A-NA_SCC-C6453N-ENG.indb 24

2009-08-05 오후 3:03:

Image 24

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s IncludedAt a Glance CameraFrame SET Preparing Installation InstallationScrew Fixing Hole Diagram Insert the cable into the Frame SET, and close the AdaptorProtective Tape from on the lens Button Frame SET Cover Camera Initial Setup Camera Address SetupCommunication Protocol Setup Use SW606, SW605, and SW604 to specify the camera addressBaud Rate Setup Setting RS-422A/RS-485 TerminationUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkConnecting with Other device Connecting to a monitorVideo terminal on the rear of monitor BNC Cable To connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu Profile  ITSNight You can configure the general settings of the camera module Camera SETCamera ID  Location Specify the display position of the camera ID Manual Adjust the iris level manually With this, you can adjust the AGC level of aIris AGCMotion DNRShutter SENS-UPYou can specify a recording mode according to the scene FlickerlessXDR DAY/NIGHTAuto Switch or Auto Focus NeededSET-AUTO SET are not available White BAL DAY/NIGHT Zoom Speed Display ZoomDisplay P/T Digital ZoomSync AGC Color SUPReverse POSI/NEGAYou can enable the motion detection and tracking functions When multiple motions continue arbitrarilyIntelligent Video AdvancedResolution Alarm OUTPrivacy Zone DisplayPreset Select the preset number Select Position and adjust PANAuto Pan Setup Settings so define them again after the operationAuto SET You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for PresetZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETFactory Defaults PasswordOSD Color Proportional P/TCommunication System InfoYou can check the system information Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeySpecifications Preset Pan Speed 600˚/sec, maximum Description PAN range 360˚EndlessManual Pan Speed 0.01˚~ 180˚/sec Tilt range -6˚~186˚Product Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후