Samsung SCC-C6453N user manual Specifications

Page 49

Specifications

Item			Description

Product Type	SMART DOME CAMERA

Power Source	AC 24 V (60 Hz)

Power Consumption	11W

TV Standard	NTSC STANDARD COLOR SYSTEM

Image Sensor	Super-HAD IT CCD

Effective Pixels	768(H) × 494(V)

TV line frequency	Horizontal : 15, 734 Hz (INT) / 15, 750 Hz (L/L)
TV line frequency	Vertical : 59.94 Hz (INT) / 60 Hz (L/L)
	Vertical : 59.94 Hz (INT) / 60 Hz (L/L)

Synchronization	INT/LINE LOCK

Resolution	Horizontal : 600 TV LINES
Resolution	Vertical : 350 TV LINES
	Vertical : 350 TV LINES

S/N Ratio	Approximately 52 dB

	SENS-UP		Illumination		Color	B/W

	Off		50IRE		2	0.2

	Off		30IRE		1.2	0.12
Minimum subject
Minimum subject	Off		15IRE		0.6	0.06
illumination	Off		15IRE		0.6	0.06
illumination
	x512		50IRE		0.004	0.0004

	x512		30IRE		0.002	0.0002

	x512		15IRE		0.001	0.0001

Signal Output	COMPOSITE VIDEO OUT : 1.0 Vp-p 75 ohms/BNC

	x43 Zoom Lens Integrated
Lens	Focal length : 3.2 ~ 138.5mm
Lens	Aperture : F1.65(Wide) F3.7(Tale)
	Aperture : F1.65(Wide) F3.7(Tale)
	- MOD(Minimum Object Distance) : 100mm

English

English _49

00890A-NA_SCC-C6453N-ENG.indb 49

2009-08-05 오후 3:03:

Image 49

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents What’s Included FeaturesCamera At a GlanceFrame SET Installation Preparing InstallationInsert the cable into the Frame SET, and close the Adaptor Screw Fixing Hole DiagramProtective Tape from on the lens Button Frame SET Cover Camera Camera Address Setup Initial SetupCommunication Protocol Setup Use SW606, SW605, and SW604 to specify the camera addressSetting RS-422A/RS-485 Termination Baud Rate SetupUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPSSame address in the network RS-422A/RS-485 Full Duplex OrganizationConnecting to a monitor Connecting with Other deviceVideo terminal on the rear of monitor BNC Cable To connect Alarm OUT To connect AlarmTo connect the controller Power Supply Connecting the adaptor cableAdaptor Board Using OSD icons How to use the keyboard controllerCamera will resume the last run operation Main Menu  ITS ProfileNight Camera SET You can configure the general settings of the camera moduleCamera ID  Location Specify the display position of the camera IDWith this, you can adjust the AGC level of a  Manual Adjust the iris level manuallyIris AGCDNR MotionShutter SENS-UPFlickerless You can specify a recording mode according to the sceneXDR DAY/NIGHTNeeded Auto Switch or Auto FocusSET-AUTO SET are not available White BAL DAY/NIGHT Display Zoom Zoom SpeedDisplay P/T Digital ZoomAGC Color SUP SyncReverse POSI/NEGAWhen multiple motions continue arbitrarily You can enable the motion detection and tracking functionsIntelligent Video AdvancedAlarm OUT ResolutionPrivacy Zone DisplayPreset Select Position and adjust PAN Select the preset numberSettings so define them again after the operation Auto Pan SetupAuto SET You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Scan Setup Pattern SetupSelect the Start and move the camera using pan/tilt/zoom ~ 511 for Preset Auto Play SetupYou can set the north direction and the zone coverage Zone SETSelect Main MENU-ZONE SET Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETPassword Factory DefaultsOSD Color Proportional P/TSystem Info CommunicationYou can check the system information Select Main MENU-SYSTEM InfoYou can set the language of the user interface LanguageFunction Key Shortcut KeysSpecifications Description PAN range 360˚Endless Preset Pan Speed 600˚/sec, maximumManual Pan Speed 0.01˚~ 180˚/sec Tilt range -6˚~186˚Product Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후