Samsung SCC-C6453N user manual Zone SET, You can set the north direction and the zone coverage

Page 41

ZONE SET

You can set the north direction and the zone coverage.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)

1. Select <MAIN MENU>-<ZONE SET>.

 MAIN MENU 

PROFILE

CAMERA SET

INTELLIGENCE

PRIVACY ZONE

PRESET

AUTO SET

ZONE SET

ALARM SET

CLOCK SET

OTHER SET

English

2.Set <AZIMUTH> to <ON>.

3.Set the north direction using the joystick and press [ENTER].

SET NORTH : In SET NORTH, press [ENTER] to set the north direction which will be the reference for all other directions.

4.Set <ZONE AREA SET> to <ON>.

ZONE SET 

AZIMUTH	OFF
ZONE AREA SET	OFF

5.When the <ZONE AREA MAP> screen appears, select a number.

6.When the <ZONE AREA SET> screen appears, set the <POSITION> and <ZONE ID SET>.

For entering the name, refer to “CAMERA ID”. (page 24)

POSITION : Sets the left/right boundaries of the zone.

ZONE AREA MAP

1 2 3 4

5 6 7 8

English _41

00890A-NA_SCC-C6453N-ENG.indb 41

2009-08-05 오후 3:03:

Image 41

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents What’s Included FeaturesFrame SET At a GlanceCamera Installation Preparing InstallationInsert the cable into the Frame SET, and close the Adaptor Screw Fixing Hole DiagramProtective Tape from on the lens Button Frame SET Cover Camera Camera Address Setup Initial SetupCommunication Protocol Setup Use SW606, SW605, and SW604 to specify the camera addressSetting RS-422A/RS-485 Termination Baud Rate SetupUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPSSame address in the network RS-422A/RS-485 Full Duplex OrganizationVideo terminal on the rear of monitor BNC Cable Connecting with Other deviceConnecting to a monitor To connect the controller To connect AlarmTo connect Alarm OUT Adaptor Board Connecting the adaptor cablePower Supply Camera will resume the last run operation How to use the keyboard controllerUsing OSD icons Main Menu  ITS ProfileNight Camera SET You can configure the general settings of the camera moduleCamera ID  Location Specify the display position of the camera IDWith this, you can adjust the AGC level of a  Manual Adjust the iris level manuallyIris AGCDNR MotionShutter SENS-UPFlickerless You can specify a recording mode according to the sceneXDR DAY/NIGHTSET-AUTO SET are not available Auto Switch or Auto FocusNeeded White BAL DAY/NIGHT Display Zoom Zoom SpeedDisplay P/T Digital ZoomAGC Color SUP SyncReverse POSI/NEGAWhen multiple motions continue arbitrarily You can enable the motion detection and tracking functionsIntelligent Video AdvancedAlarm OUT ResolutionPrivacy Zone DisplayPreset Select Position and adjust PAN Select the preset numberSettings so define them again after the operation Auto Pan SetupAuto SET You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Select the Start and move the camera using pan/tilt/zoom Pattern SetupScan Setup ~ 511 for Preset Auto Play SetupSelect Main MENU-ZONE SET Zone SETYou can set the north direction and the zone coverage Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETPassword Factory DefaultsOSD Color Proportional P/TSystem Info CommunicationYou can check the system information Select Main MENU-SYSTEM InfoYou can set the language of the user interface LanguageFunction Key Shortcut KeysSpecifications Description PAN range 360˚Endless Preset Pan Speed 600˚/sec, maximumManual Pan Speed 0.01˚~ 180˚/sec Tilt range -6˚~186˚Product Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후