Samsung SCC-C6453N user manual Privacy Zone, Display, Sensitivity, Resolution, Alarm OUT

Page 34

setup

DISPLAY

When selected <ON>, it displays the motion detected and detection of configured advanced function.

SENSITIVITY

Sets the sensitivity of motion sensor.

RESOLUTION

The bigger the resolution setting, the smaller the object that can be detected.

ALARM OUT

When selected <ON>, it outputs alarm signal when the motion is detected and on a detection of configured advanced function.

ALARM OUT

MOTIONON

FIXED/MOVEDON

PRIVACY ZONE

You can set up to 12 privacy zones that will be hided for privacy of the subject when recording.

Zone Setup

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)

1.Select <MAIN MENU>-<PRIVACY ZONE>.

2.Select the number of the zone and press [ENTER].

The Zone setup screen appears.

3.Select the <SET P/T/Z> and press [ENTER].

Using the joystick, adjust the camera’s pan, tilt and zoom.

PRIVACY ZONE 

1	2	3	4	5	6
7	8	9	10	11	12
PRIVACY SET					ON
STYLE					MOSAIC1

34_ setup

00890A-NA_SCC-C6453N-ENG.indb 34

2009-08-05 오후 3:03:

Image 34

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s IncludedCamera At a GlanceFrame SET Preparing Installation InstallationScrew Fixing Hole Diagram Insert the cable into the Frame SET, and close the AdaptorProtective Tape from on the lens Button Frame SET Cover Camera Communication Protocol Setup Initial SetupCamera Address Setup Use SW606, SW605, and SW604 to specify the camera addressUse pins #5, #6 of SW603 to set the baud rate Baud Rate SetupSetting RS-422A/RS-485 Termination Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkConnecting to a monitor Connecting with Other deviceVideo terminal on the rear of monitor BNC Cable To connect Alarm OUT To connect AlarmTo connect the controller Power Supply Connecting the adaptor cableAdaptor Board Using OSD icons How to use the keyboard controllerCamera will resume the last run operation Main Menu Profile  ITSNight Camera ID You can configure the general settings of the camera moduleCamera SET  Location Specify the display position of the camera IDIris  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a AGCShutter MotionDNR SENS-UPXDR You can specify a recording mode according to the sceneFlickerless DAY/NIGHTNeeded Auto Switch or Auto FocusSET-AUTO SET are not available White BAL DAY/NIGHT Display P/T Zoom SpeedDisplay Zoom Digital ZoomReverse SyncAGC Color SUP POSI/NEGAIntelligent Video You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily AdvancedPrivacy Zone ResolutionAlarm OUT DisplayPreset Select the preset number Select Position and adjust PANAuto SET Auto Pan SetupSettings so define them again after the operation You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Scan Setup Pattern SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for PresetYou can set the north direction and the zone coverage Zone SETSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETOSD Color Factory DefaultsPassword Proportional P/TYou can check the system information CommunicationSystem Info Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeySpecifications Manual Pan Speed 0.01˚~ 180˚/sec Preset Pan Speed 600˚/sec, maximumDescription PAN range 360˚Endless Tilt range -6˚~186˚Product Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후