Samsung SCC-C6453N user manual Communication, System Info, You can check the system information

Page 46

setup

COMMUNICATION

You can set the RS-485 communications setting in regard of the camera.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)

1.Select <MAIN MENU>-<COMMUNICATION>.

2.Select each item and set appropriately.

PRIORITY : Set the priority by selecting <HW> or <SW>.

When selected <HW>, the protocol, baud rate and address settings will follow those settings of the adaptor switch.

PROTOCOL, BAUD RATE, ADDRESS : When selected <SW>, you can manually set the protocol, baud rate and address.

COMMUNICATION 

RS485
PRIORITY	HW
PROTOCOL	SAMSUNG
	HALF
BAUD RATE	9600
ADDRESS	0

SYSTEM INFO

You can check the system information.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)

1.Select <MAIN MENU>-<SYSTEM INFO>.

2.The current system information is displayed.

SYSTEM INFO 

TYPE	4_PTZ_NOR_N
PROTOCOL	SAMSUNG
ADDRESS	0
COMM. TYPE	HW, RS485, HALF
BAUD RATE	9600
SERIAL NO.	000000000000000
CAMERA VER.	v1.00_00000
ALARM VER.	v1.00_00000

46_ setup

00890A-NA_SCC-C6453N-ENG.indb 46

2009-08-05 오후 3:03:

Image 46

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s IncludedCamera At a GlanceFrame SET Preparing Installation InstallationScrew Fixing Hole Diagram Insert the cable into the Frame SET, and close the AdaptorProtective Tape from on the lens Button Frame SET Cover Camera Communication Protocol Setup Initial SetupCamera Address Setup Use SW606, SW605, and SW604 to specify the camera addressUse pins #5, #6 of SW603 to set the baud rate Baud Rate SetupSetting RS-422A/RS-485 Termination Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkConnecting to a monitor Connecting with Other deviceVideo terminal on the rear of monitor BNC Cable To connect Alarm OUT To connect AlarmTo connect the controller Power Supply Connecting the adaptor cableAdaptor Board Using OSD icons How to use the keyboard controllerCamera will resume the last run operation Main Menu Profile  ITSNight Camera ID You can configure the general settings of the camera moduleCamera SET  Location Specify the display position of the camera IDIris  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a AGCShutter MotionDNR SENS-UPXDR You can specify a recording mode according to the sceneFlickerless DAY/NIGHTNeeded Auto Switch or Auto FocusSET-AUTO SET are not available White BAL DAY/NIGHT Display P/T Zoom SpeedDisplay Zoom Digital ZoomReverse SyncAGC Color SUP POSI/NEGAIntelligent Video You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily AdvancedPrivacy Zone ResolutionAlarm OUT DisplayPreset Select the preset number Select Position and adjust PANAuto SET Auto Pan SetupSettings so define them again after the operation You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Scan Setup Pattern SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for PresetYou can set the north direction and the zone coverage Zone SETSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETOSD Color Factory DefaultsPassword Proportional P/TYou can check the system information CommunicationSystem Info Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeySpecifications Manual Pan Speed 0.01˚~ 180˚/sec Preset Pan Speed 600˚/sec, maximumDescription PAN range 360˚Endless Tilt range -6˚~186˚Product Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후