Samsung SCC-C6453N user manual Initial Setup, Camera Address Setup, Communication Protocol Setup

Page 14

installation & connection

INITIAL SETUP

Camera Address Setup

Use SW606, SW605, and SW604 to specify the camera address.

You can specify between 0 and 255 for the address, where the hundreds digit is with SW606, the tens digit with SW605, and the ones digit with SW604.

ex) Camera address: If the address is 1, follow the steps in the figure below.

SW606

SW605

SW604

(x100)

(x10)

(x1)

Communication Protocol Setup

Use pins #1~#4 of SW603 to specify the communication protocol.

PIN	PIN1	PIN2	PIN3	PIN4
Comp	PIN1	PIN2	PIN3	PIN4
Comp
A	OFF	OFF	OFF	OFF
B	ON	OFF	OFF	OFF
C	OFF	ON	OFF	OFF
D	ON	ON	OFF	OFF
E	OFF	OFF	ON	OFF
F	ON	OFF	ON	OFF
G	OFF	ON	ON	OFF
H	ON	ON	ON	OFF
I	OFF	OFF	OFF	ON
J	ON	OFF	OFF	ON
K	OFF	ON	OFF	ON
L	ON	ON	OFF	ON
M	OFF	OFF	ON	ON
N	ON	OFF	ON	ON
O	OFF	ON	ON	ON
P	ON	ON	ON	ON

A : SAMSUNG HALF

B : SAMSUNG FULL

<Bottom of the camera holder>

1_ installation & connection

00890A-NA_SCC-C6453N-ENG.indb 14

2009-08-05 오후 3:03:

Image 14

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s IncludedFrame SET At a GlanceCamera Preparing Installation InstallationScrew Fixing Hole Diagram Insert the cable into the Frame SET, and close the AdaptorProtective Tape from on the lens Button Frame SET Cover Camera Communication Protocol Setup Initial SetupCamera Address Setup Use SW606, SW605, and SW604 to specify the camera addressUse pins #5, #6 of SW603 to set the baud rate Baud Rate SetupSetting RS-422A/RS-485 Termination Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkVideo terminal on the rear of monitor BNC Cable Connecting with Other deviceConnecting to a monitor To connect the controller To connect AlarmTo connect Alarm OUT Adaptor Board Connecting the adaptor cablePower Supply Camera will resume the last run operation How to use the keyboard controllerUsing OSD icons Main Menu Profile  ITSNight Camera ID You can configure the general settings of the camera moduleCamera SET  Location Specify the display position of the camera IDIris  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a AGCShutter MotionDNR SENS-UPXDR You can specify a recording mode according to the sceneFlickerless DAY/NIGHTSET-AUTO SET are not available Auto Switch or Auto FocusNeeded White BAL DAY/NIGHT Display P/T Zoom SpeedDisplay Zoom Digital ZoomReverse SyncAGC Color SUP POSI/NEGAIntelligent Video You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily AdvancedPrivacy Zone ResolutionAlarm OUT DisplayPreset Select the preset number Select Position and adjust PANAuto SET Auto Pan SetupSettings so define them again after the operation You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Select the Start and move the camera using pan/tilt/zoom Pattern SetupScan Setup Auto Play Setup ~ 511 for PresetSelect Main MENU-ZONE SET Zone SETYou can set the north direction and the zone coverage Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETOSD Color Factory DefaultsPassword Proportional P/TYou can check the system information CommunicationSystem Info Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeySpecifications Manual Pan Speed 0.01˚~ 180˚/sec Preset Pan Speed 600˚/sec, maximumDescription PAN range 360˚Endless Tilt range -6˚~186˚Product Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후