Samsung SCC-C6453N user manual Select the preset number, Select Position and adjust PAN

Page 36

setup

2.Select the preset number.

	 PRESET 
0	1	2	3	4
5	6	7	8	9
10	11	12	13	14
15	16	17	18	19
20	21	22	23	24
25	26	27	28	29
30	31	 1/16
		 1/16	

3.Select <POSITION> and adjust <PAN/

	TILT/ZOOM> to the desired setup using	PRESET NO. 1
	the joystick.	POSITION
	4. Set <PRESET ID> to <ON> and enter the	PRESET ID	ON
	4. Set <PRESET ID> to <ON> and enter the	PRESET SPEED	[5]
	name.	PRESET SPEED	[5]
	name.	DWELL TIME	3SEC
	 For entering the name, refer to “CAMERA ID”.	IMAGE HOLD	OFF
	 For entering the name, refer to “CAMERA ID”.	CAMERA SET	ON
	(page 24)

5.Select <PRESET SPEED> and adjust the

pan/tilt speed of the preset.

6.Set the <DWELL TIME> that defines the

camera's hold duration and <IMAGE HOLD> of the preset.

If you set the <IMAGE HOLD> to <ON>, the video image will be held still until the camera reaches the preset position.

7.Set <CAMERA SET> to <ON>.

You can adjust camera setups for each preset.

For details on setting <IRIS>, <WHITE BAL> and <FOCUS MODE>, refer to “CAMERA SET”. (pages 24 ~ 32)

CAMERA SET
IRIS	ALC
WHITE BAL
FOCUS MODE	MF

36_ setup

00890A-NA_SCC-C6453N-ENG.indb 36

2009-08-05 오후 3:03:

Image 36

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s IncludedAt a Glance CameraFrame SET Preparing Installation InstallationScrew Fixing Hole Diagram Insert the cable into the Frame SET, and close the AdaptorProtective Tape from on the lens Button Frame SET Cover Camera Initial Setup Camera Address SetupCommunication Protocol Setup Use SW606, SW605, and SW604 to specify the camera addressBaud Rate Setup Setting RS-422A/RS-485 TerminationUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkConnecting with Other device Connecting to a monitorVideo terminal on the rear of monitor BNC Cable To connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu Profile  ITSNight You can configure the general settings of the camera module Camera SETCamera ID  Location Specify the display position of the camera ID Manual Adjust the iris level manually With this, you can adjust the AGC level of aIris AGCMotion DNRShutter SENS-UPYou can specify a recording mode according to the scene FlickerlessXDR DAY/NIGHTAuto Switch or Auto Focus NeededSET-AUTO SET are not available White BAL DAY/NIGHT Zoom Speed Display ZoomDisplay P/T Digital ZoomSync AGC Color SUPReverse POSI/NEGAYou can enable the motion detection and tracking functions When multiple motions continue arbitrarilyIntelligent Video AdvancedResolution Alarm OUTPrivacy Zone DisplayPreset Select the preset number Select Position and adjust PANAuto Pan Setup Settings so define them again after the operationAuto SET You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for PresetZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETFactory Defaults PasswordOSD Color Proportional P/TCommunication System InfoYou can check the system information Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeySpecifications Preset Pan Speed 600˚/sec, maximum Description PAN range 360˚EndlessManual Pan Speed 0.01˚~ 180˚/sec Tilt range -6˚~186˚Product Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후