Samsung SCC-C6453N user manual Important safety instructions

Page 6

overview

important safety instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified

by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus

_ overview

00890A-NA_SCC-C6453N-ENG.indb 6

2009-08-05 오후 3:03:

Image 6

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents Features What’s IncludedAt a Glance CameraFrame SET Preparing Installation InstallationScrew Fixing Hole Diagram Insert the cable into the Frame SET, and close the AdaptorProtective Tape from on the lens Button Frame SET Cover Camera Communication Protocol Setup Initial SetupCamera Address Setup Use SW606, SW605, and SW604 to specify the camera addressUse pins #5, #6 of SW603 to set the baud rate Baud Rate SetupSetting RS-422A/RS-485 Termination Factory default is 9600 BPSRS-422A/RS-485 Full Duplex Organization Same address in the networkConnecting with Other device Connecting to a monitorVideo terminal on the rear of monitor BNC Cable To connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu Profile  ITSNight Camera ID You can configure the general settings of the camera moduleCamera SET  Location Specify the display position of the camera IDIris  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a AGCShutter MotionDNR SENS-UPXDR You can specify a recording mode according to the sceneFlickerless DAY/NIGHTAuto Switch or Auto Focus NeededSET-AUTO SET are not available White BAL DAY/NIGHT Display P/T Zoom SpeedDisplay Zoom Digital ZoomReverse SyncAGC Color SUP POSI/NEGAIntelligent Video You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily AdvancedPrivacy Zone ResolutionAlarm OUT DisplayPreset Select the preset number Select Position and adjust PANAuto SET Auto Pan SetupSettings so define them again after the operation You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom Auto Play Setup ~ 511 for PresetZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Alarm SET Select Main MENU-ALARM SET Auto SET Sets the pattern and scan Clock SET Other SETOSD Color Factory DefaultsPassword Proportional P/TYou can check the system information CommunicationSystem Info Select Main MENU-SYSTEM InfoLanguage You can set the language of the user interfaceShortcut Keys Function KeySpecifications Manual Pan Speed 0.01˚~ 180˚/sec Preset Pan Speed 600˚/sec, maximumDescription PAN range 360˚Endless Tilt range -6˚~186˚Product Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후