Samsung SCC-C6453N user manual Main Menu

Page 21

Main Menu

This is the first screen you ever see when you turn on the camera where you can set the camera environment to your needs.

For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)

PROFILE

Select a mode appropriate to the camera installation environment.

CAMERA SET

You can configure the camera settings.

INTELLIGENCE

Offers motion detection and tracking functions.

PRIVACY ZONE

You can configure the privacy settings.

PRESET

You can set the PRESET POSITION and

DURATION.

AUTO SET

Contains sub menu items of AUTO PAN, PATTERN, and SCAN.

ZONE SET

You can set the standard azimuth and zone area for the camera.

ALARM SET

You can set the alarm priority and I/O sequence.

CLOCK SET

You can set the display time and format.

OTHER SET

 MAIN MENU 

PROFILE

CAMERA SET INTELLIGENCE PRIVACY ZONE PRESET AUTO SET ZONE SET ALARM SET CLOCK SET OTHER SET

COMMUNICATION SYSTEM INFO LANGUAGE

English

You can reset the camera, or adjust the OSD color to your preference.

COMMUNICATION

Configures the settings pertaining to RS-485 communication.

SYSTEM INFO

Shows the system information such as the camera version or communication settings.

LANGUAGE

Select a preferred one from the supported languages.

English _21

00890A-NA_SCC-C6453N-ENG.indb 21

2009-08-05 오후 3:03:

Image 21

Contents Smart Dome Camera Overview English Overview FCC Statement Important safety instructions Contents What’s Included FeaturesAt a Glance CameraFrame SET Installation Preparing InstallationInsert the cable into the Frame SET, and close the Adaptor Screw Fixing Hole DiagramProtective Tape from on the lens Button Frame SET Cover Camera Camera Address Setup Initial SetupCommunication Protocol Setup Use SW606, SW605, and SW604 to specify the camera addressSetting RS-422A/RS-485 Termination Baud Rate SetupUse pins #5, #6 of SW603 to set the baud rate Factory default is 9600 BPSSame address in the network RS-422A/RS-485 Full Duplex OrganizationConnecting with Other device Connecting to a monitorVideo terminal on the rear of monitor BNC Cable To connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu  ITS ProfileNight Camera SET You can configure the general settings of the camera moduleCamera ID  Location Specify the display position of the camera IDWith this, you can adjust the AGC level of a  Manual Adjust the iris level manuallyIris AGCDNR MotionShutter SENS-UPFlickerless You can specify a recording mode according to the sceneXDR DAY/NIGHTAuto Switch or Auto Focus NeededSET-AUTO SET are not available White BAL DAY/NIGHT Display Zoom Zoom SpeedDisplay P/T Digital ZoomAGC Color SUP SyncReverse POSI/NEGAWhen multiple motions continue arbitrarily You can enable the motion detection and tracking functionsIntelligent Video AdvancedAlarm OUT ResolutionPrivacy Zone DisplayPreset Select Position and adjust PAN Select the preset numberSettings so define them again after the operation Auto Pan SetupAuto SET You can set the Auto PAN, PATTERN, and Auto PlayPosition Direction Left Endless OFF Speed Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom ~ 511 for Preset Auto Play SetupZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETPassword Factory DefaultsOSD Color Proportional P/TSystem Info CommunicationYou can check the system information Select Main MENU-SYSTEM InfoYou can set the language of the user interface LanguageFunction Key Shortcut KeysSpecifications Description PAN range 360˚Endless Preset Pan Speed 600˚/sec, maximumManual Pan Speed 0.01˚~ 180˚/sec Tilt range -6˚~186˚Product Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후