Samsung SCC-C6453N user manual English 

Page 3

6.Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

7.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

8.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

9.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)

10.When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock

11.Do not expose the product to the direct airflow from an air conditioner. Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between internal and external of the dome camera.

12.If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with silicon, so that the external air can not flow inside the housing.

Otherwise, external high, humid air may flow inside the housing, pooling moisture or vapor inside the product due to a difference between internal and external temperature.

English

English _

00890A-NA_SCC-C6453N-ENG.indb 3

2009-08-05 오후 3:03:

Image 3
Contents Smart Dome Camera Overview English  Overview FCC Statement Important safety instructions Contents What’s Included FeaturesAt a Glance CameraFrame SET Installation Preparing InstallationInsert the cable into the Frame SET, and close the Adaptor Screw Fixing Hole DiagramProtective Tape from on the lens Button Frame SET Cover Camera Use SW606, SW605, and SW604 to specify the camera address Initial SetupCamera Address Setup Communication Protocol SetupFactory default is 9600 BPS Baud Rate SetupSetting RS-422A/RS-485 Termination Use pins #5, #6 of SW603 to set the baud rateSame address in the network RS-422A/RS-485 Full Duplex OrganizationConnecting with Other device Connecting to a monitorVideo terminal on the rear of monitor BNC Cable To connect Alarm To connect Alarm OUTTo connect the controller Connecting the adaptor cable Power SupplyAdaptor Board How to use the keyboard controller Using OSD iconsCamera will resume the last run operation Main Menu  ITS ProfileNight  Location Specify the display position of the camera ID You can configure the general settings of the camera moduleCamera SET Camera IDAGC  Manual Adjust the iris level manuallyWith this, you can adjust the AGC level of a IrisSENS-UP MotionDNR ShutterDAY/NIGHT You can specify a recording mode according to the sceneFlickerless XDRAuto Switch or Auto Focus NeededSET-AUTO SET are not available White BAL DAY/NIGHT Digital Zoom Zoom SpeedDisplay Zoom Display P/TPOSI/NEGA SyncAGC Color SUP ReverseAdvanced You can enable the motion detection and tracking functionsWhen multiple motions continue arbitrarily Intelligent VideoDisplay ResolutionAlarm OUT Privacy ZonePreset Select Position and adjust PAN Select the preset numberYou can set the Auto PAN, PATTERN, and Auto Play Auto Pan SetupSettings so define them again after the operation Auto SETPosition Direction Left Endless OFF Speed Pattern Setup Scan SetupSelect the Start and move the camera using pan/tilt/zoom ~ 511 for Preset Auto Play SetupZone SET You can set the north direction and the zone coverageSelect Main MENU-ZONE SET Select Main MENU-ALARM SET Alarm SET Auto SET Sets the pattern and scan Other SET Clock SETProportional P/T Factory DefaultsPassword OSD ColorSelect Main MENU-SYSTEM Info CommunicationSystem Info You can check the system informationYou can set the language of the user interface LanguageFunction Key Shortcut KeysSpecifications Tilt range -6˚~186˚ Preset Pan Speed 600˚/sec, maximumDescription PAN range 360˚Endless Manual Pan Speed 0.01˚~ 180˚/secProduct Appearance 00890A-NASCC-C6453N-ENG.indb 2009-08-05 오후