Pioneer PRS-D1000M owner manual Connecting the Speaker Wires, Single Amplifier, Bridged Mode

Page 10

Connecting the Unit

Connecting the Speaker Wires

Connect the speaker leads and set MODE SELECT switch and POWER MODE switch to suit the configura- tion according to the figures shown below and the next page.

•When synchronously connecting two or more amplifiers in combination, only use these amplifiers. Do not mix these amplifiers with other amplifiers.

•When synchronously connecting two or more amplifiers in combination, set the gain control, subsonic select switch, cut off frequency control for LPF and bass boost control on the amplifier that has been set to MASTER with the MODE SELECT switch. These settings are inactive when set on an amplifier set to SYNC or SYNC INV.

CAUTION

Diagram A - Proper

Diagram B - Improper

4 Ω

4 Ω

Speaker

Speaker

2 Ω

2 Ω

Speaker

Speaker

2 Ω Bridged Mode

1 Ω Bridged Mode

Do NOT install or use this amplifier by wiring speakers rated at 2 Ω (or lower) in parallel to achieve a 1 Ω (or lower) bridged mode (Diagram B).

Amplifier damage, smoke, and overheating could result from improper bridging. The amplifier surface could also become hot to the touch and minor burns could result.

To properly install or use a bridged mode and achieve a 2 Ω load, wire two 4 Ω speakers in parallel with Left + and Right – (Diagram A) or use a single 2 Ω speaker.

If the synthetic impedance is from 2 Ω to less than 4 Ω, always make sure to set the POWER MODE switch to the HI-CURRENT position.

In addition, refer to the speaker instruction manual for information on the correct connection procedure.

Single Amplifier

MODE SELECT switch must

Connect to a car stereo.

be in MASTER position.

For details, see the “Connection Diagram”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 Ω to 8 Ω

•Use speakers having an impedance from 1 Ω to 8 Ω.

•The setting of the POWER MODE switch varies according to the speaker impedance. See the “Setting the Unit” section for details.

9

Page 9 Page 11
Image 10
Page 9 Page 11
Contents PRS-D1000M English Français EspañolContents Before Using This ProductProduct Registration About This ProductSubsonic Select Switch Setting the UnitPower Indicator Bass Boost Control SwitchPower Mode Switch Mode Select SwitchInput Switch Gain ControlConnecting the Unit To prevent damage and/or injuryConnection Diagram Connecting the Power Terminal Connections when using the speaker input Connecting the Speaker Output TerminalsUsing the Speaker Input Use pliers, etc., to crimp lugs to wires Lug Speaker wireSingle Amplifier Connecting the Speaker WiresBridged Mode SpeakerEnglish Español Two Amplifier Ex. BridgeTwo Amplifier Must be in Master position Mode Select switch must be Sync INV positionFour Amplifier Ex. Bridge 16 ΩFour Amplifier Mode Select switch Must be in Master position To 8 ΩConnecting wire with RCA Sync pin plugs sold separately English Español DeutschInstallation To prevent malfunction and/or injuryExample of installation on the floor mat or on the chassis Replacing the terminal coverSpecifications English Español Deutsch Français Avant d’utiliser cet appareil Service après-vente pour un produit PioneerTable des matières Etats-UnisEnregistrement du produit Quelques mots concernant cet appareilTémoin ’alimentation Commande de l’accentua- tion des gravesRéglage de l’appareil Couvre-bornesCommande de la fréquence de coupure pour LPF Commutateur Mode SelectCommande du gain Commutateur Power ModeRaccordement de l’appareil Pour éviter toute anomalie ou blessureSchéma de raccordement English Français DeutschRaccordement de la borne d’alimentation English Français Deutsch Français Utilisation de l’entrée de haut-parleurRaccordement des bornes de sortie vers les haut-parleurs Faites glisser le sélecteur d’entrée sur la droiteAmplificateur unique Diagramme a CorrectConnexion des câbles des haut-parleurs EnceinteEnglish Deux amplificateursDe prises Cinch RCA Quatre amplificateurs connexion en pont exConnexion des câbles des haut-parleurs vendus séparément Connexion des Vendus séparémentLa section Schéma de raccordement Le commutateur Mode Select Doit être sur la position MasterQuatre amplificateurs À 8 Ω Doit être sur la position Sync’installez pas l’appareil Pour éviter toute anomalie de fonctionnement ou blessureRemise en place du couvre-bornes English Français Deutsch Français Italiano NederlandsCaractéristiques techniques Page Servicio posventa para productos Pioneer ContenidoAntes de usar este producto EE.UUSobre este producto Registro del productoContacte a su distribuidor si no puede detectar la causa Cubierta de terminales Ajuste de esta unidadControl de refuerzo de graves Interruptor selector subsónicoControl de ganancia Interruptor Mode SelectInterruptor Power Mode Control de frecuencia de corte para LPFConexión de la unidad Para evitar daños y/o lesionesDiagrama de conexión Conexión del terminal de alimentación Altavoz Cable de altavoz Conexión del terminal de salida de altavozUso de la entrada de altavoz La toma de entrada RCA de esta unidadAmplificador simple Diagrama a CorrectoConexión de los cables de altavoces De 4 Ω Voz De 2 ΩEspañol Español Dos amplificadores Puente externoDos amplificadores Cuatro amplificadores Puente externo Cuatro amplificadores El interruptor Mode Select Conecte a un equipoA 8 Ω El interruptor Mode Select Para los detallesInstalación Para evitar fallas de funcionamiento y/o lesionesChasis Recolocación de la cubierta de terminalesCubierta de terminales De diámetroEspecificaciones English Español Français Pioneer Corporation
Related manuals
Manual 8 pages 61.28 Kb

PRS-D1000M specifications

The Pioneer PRS-D1000M is a versatile and powerful car amplifier designed to enhance the audio experience in vehicles. Known for its robust performance and innovative features, this amplifier is ideal for enthusiasts seeking to elevate their sound system.

One of the main features of the PRS-D1000M is its impressive power output. It delivers up to 1000 watts of maximum power, allowing users to drive high-performance subwoofers and achieve deep, thunderous bass. With its RMS power rating of 500 watts at 2 ohms, this amplifier ensures that even the most demanding audio setups can be accommodated, making it suitable for both daily driving and competition use.

The PRS-D1000M employs Class D technology, which is crucial for efficiency and heat management. Class D amplifiers convert a higher percentage of the power drawn from the vehicle's electrical system into usable output, resulting in less heat generation and lower energy consumption. This is particularly beneficial for car audio systems, where space and power are often at a premium.

Another notable characteristic is the built-in low-pass filter, which allows users to tailor the sound by eliminating higher frequencies that can muddy the bass response. The variable frequency adjustment lets users set the cutoff point according to their specific subwoofer and listening preferences, resulting in a more refined audio experience.

The Pioneer PRS-D1000M also features a bass boost function, which lets users increase low-frequency output for a more pronounced bass response. This is especially useful for those who love bass-heavy music genres. The amplifier's compact design makes it easy to install in various locations within the vehicle, ensuring that it doesn't compromise valuable space.

Furthermore, the amplifier is equipped with RCA inputs for seamless integration with other audio components. It includes speaker-level inputs, allowing it to connect to factory audio systems without needing to replace the head unit.

In conclusion, the Pioneer PRS-D1000M is engineered for performance, efficiency, and flexibility. With its powerful output, advanced technologies, and user-friendly features, it is an excellent choice for anyone looking to upgrade their car's audio system and enjoy a superior listening experience on the road.
Top Page Image Contents