Pioneer PRS-D1000M owner manual Specifications

Page 16

Specifications

Power source

14.4 V DC (10.8 V to 15.1 V allowable)

Grounding system

 

Negative type

Current consumption

39 A (at continuous power, 4 Ω)

Average current drawn*

12 A (4 Ω for one channel)

 

 

20 A (2 Ω for one channel)

 

 

28 A (1 Ω for one channel)

Fuse (external)

 

40 A ⋅ 2

Dimensions

304 (W) ⋅ 56 (H) ⋅ 202 (D) mm

 

 

[12 (W) ⋅ 2-1/4 (H) ⋅ 8 (D) in.]

Weight

3.0 kg (6.6 lbs.) (Leads for wiring not included)

Maximum power output

800 W ⋅ 1 (4 Ω) / 1 200 W ⋅ 1 (1 Ω to 2 Ω)

Continuous power (14.4 V)

NORMAL mode: 4 Ω, 20 Hz to 240 Hz,

1.0% THD, 400 W ⋅ 1

 

 

2 Ω, 100 Hz,

1.0% THD, 600 W ⋅ 1

 

HI-CURRENT mode: 4 Ω, 20 Hz to 240 Hz,

1.0% THD, 150 W ⋅ 1

 

 

2 Ω, 100 Hz,

1.0% THD, 300 W ⋅ 1

 

 

1 Ω, 100 Hz,

1.0% THD, 600 W ⋅ 1

Load impedance

4 Ω (1 Ω to 8 Ω allowable)

Frequency response

10 Hz to 240 Hz (+0 dB, –3 dB)

S/N ratio

 

92 dB (IHF-A network)

Distortion

 

0.5 % (10 W, 100 Hz)

Low pass filter

Cut off frequency: 40 Hz to 240 Hz

 

 

Cut off slope: –18 dB/oct

Subsonic filter (HPF)

 

Frequency: 20 Hz

 

 

 

Slope: –18 dB

Bass boost

 

Frequency: 50 Hz

 

 

 

Level: 0 / 6 / 9 / 12 dB

Gain control

 

RCA: 400 mV to 6.5 V

 

 

 

SP: 1.6 V to 26 V

Maximum input level / impedance

 

RCA: 6.5 V / 22 kΩ

 

 

 

SP: 26 V / 90 kΩ

 

 

 

Power output

NORMAL mode: 400 W RMS ⋅ 1 channel

 

 

(at 4 Ω and

1% THD+N)

 

 

600 W RMS ⋅ 1 channel

 

 

(at 100 Hz , 2 Ω and

1% THD+N)

 

 

HI-CURRENT mode: 150 W RMS ⋅ 1 channel

 

 

(at 4 Ω and

1% THD+N)

 

 

300 W RMS ⋅ 1 channel

 

 

(at 100 Hz , 2 Ω and

1% THD+N)

 

 

600 W RMS ⋅ 1 channel

 

 

(at 100 Hz , 1 Ω and

1% THD+N)

 

S/N ratio

66 dBA (reference: 1 W into 4 Ω)

 

 

 

 

 

Note:

•Specifications and the design are subject to possible modification without notice due to improvements.

*Average current drawn

•The average current drawn is nearly the maximum current drawn by this unit when an audio signal is input. Use this value when working out total current drawn by multiple power amplifiers.

15

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PRS-D1000M English Français EspañolContents Before Using This ProductProduct Registration About This ProductSetting the Unit Power IndicatorSubsonic Select Switch Bass Boost Control SwitchMode Select Switch Input SwitchPower Mode Switch Gain ControlConnecting the Unit To prevent damage and/or injuryConnection Diagram Connecting the Power Terminal Connecting the Speaker Output Terminals Using the Speaker InputConnections when using the speaker input Use pliers, etc., to crimp lugs to wires Lug Speaker wireConnecting the Speaker Wires Bridged ModeSingle Amplifier SpeakerEnglish Español Two Amplifier Ex. BridgeTwo Amplifier Mode Select switch must be Sync INV position Four Amplifier Ex. BridgeMust be in Master position 16 ΩMode Select switch Must be in Master position To 8 Ω Connecting wire with RCA Sync pin plugs sold separatelyFour Amplifier English Español DeutschInstallation To prevent malfunction and/or injuryExample of installation on the floor mat or on the chassis Replacing the terminal coverSpecifications English Español Deutsch Français Service après-vente pour un produit Pioneer Table des matièresAvant d’utiliser cet appareil Etats-UnisEnregistrement du produit Quelques mots concernant cet appareilCommande de l’accentua- tion des graves Réglage de l’appareilTémoin ’alimentation Couvre-bornesCommutateur Mode Select Commande du gainCommande de la fréquence de coupure pour LPF Commutateur Power ModeRaccordement de l’appareil Pour éviter toute anomalie ou blessureSchéma de raccordement English Français DeutschRaccordement de la borne d’alimentation Utilisation de l’entrée de haut-parleur Raccordement des bornes de sortie vers les haut-parleursEnglish Français Deutsch Français Faites glisser le sélecteur d’entrée sur la droiteDiagramme a Correct Connexion des câbles des haut-parleursAmplificateur unique EnceinteEnglish Deux amplificateursQuatre amplificateurs connexion en pont ex Connexion des câbles des haut-parleurs vendus séparémentDe prises Cinch RCA Connexion des Vendus séparémentLe commutateur Mode Select Doit être sur la position Master Quatre amplificateursLa section Schéma de raccordement À 8 Ω Doit être sur la position Sync’installez pas l’appareil Pour éviter toute anomalie de fonctionnement ou blessureRemise en place du couvre-bornes English Français Deutsch Français Italiano NederlandsCaractéristiques techniques Page Contenido Antes de usar este productoServicio posventa para productos Pioneer EE.UUSobre este producto Registro del productoContacte a su distribuidor si no puede detectar la causa Ajuste de esta unidad Control de refuerzo de gravesCubierta de terminales Interruptor selector subsónicoInterruptor Mode Select Interruptor Power ModeControl de ganancia Control de frecuencia de corte para LPFConexión de la unidad Para evitar daños y/o lesionesDiagrama de conexión Conexión del terminal de alimentación Conexión del terminal de salida de altavoz Uso de la entrada de altavozAltavoz Cable de altavoz La toma de entrada RCA de esta unidadDiagrama a Correcto Conexión de los cables de altavocesAmplificador simple De 4 Ω Voz De 2 ΩEspañol Español Dos amplificadores Puente externoDos amplificadores Cuatro amplificadores Puente externo El interruptor Mode Select Conecte a un equipo A 8 Ω El interruptor Mode SelectCuatro amplificadores Para los detallesInstalación Para evitar fallas de funcionamiento y/o lesionesRecolocación de la cubierta de terminales Cubierta de terminalesChasis De diámetroEspecificaciones English Español Français Pioneer Corporation
Related manuals
Manual 8 pages 61.28 Kb

PRS-D1000M specifications

The Pioneer PRS-D1000M is a versatile and powerful car amplifier designed to enhance the audio experience in vehicles. Known for its robust performance and innovative features, this amplifier is ideal for enthusiasts seeking to elevate their sound system.

One of the main features of the PRS-D1000M is its impressive power output. It delivers up to 1000 watts of maximum power, allowing users to drive high-performance subwoofers and achieve deep, thunderous bass. With its RMS power rating of 500 watts at 2 ohms, this amplifier ensures that even the most demanding audio setups can be accommodated, making it suitable for both daily driving and competition use.

The PRS-D1000M employs Class D technology, which is crucial for efficiency and heat management. Class D amplifiers convert a higher percentage of the power drawn from the vehicle's electrical system into usable output, resulting in less heat generation and lower energy consumption. This is particularly beneficial for car audio systems, where space and power are often at a premium.

Another notable characteristic is the built-in low-pass filter, which allows users to tailor the sound by eliminating higher frequencies that can muddy the bass response. The variable frequency adjustment lets users set the cutoff point according to their specific subwoofer and listening preferences, resulting in a more refined audio experience.

The Pioneer PRS-D1000M also features a bass boost function, which lets users increase low-frequency output for a more pronounced bass response. This is especially useful for those who love bass-heavy music genres. The amplifier's compact design makes it easy to install in various locations within the vehicle, ensuring that it doesn't compromise valuable space.

Furthermore, the amplifier is equipped with RCA inputs for seamless integration with other audio components. It includes speaker-level inputs, allowing it to connect to factory audio systems without needing to replace the head unit.

In conclusion, the Pioneer PRS-D1000M is engineered for performance, efficiency, and flexibility. With its powerful output, advanced technologies, and user-friendly features, it is an excellent choice for anyone looking to upgrade their car's audio system and enjoy a superior listening experience on the road.
Top Page Image Contents