Sears NTL19010.0 Chest Heart Rate Monitor, HOW to PUT on the Heart Rate Monitor, Troubleshooting

Page 13

THE CHEST HEART RATE MONITOR

HOW TO PUT ON THE HEART RATE MONITOR

The heart rate

 

 

monitor consists of

 

 

a chest strap and a

 

Chest

sensor. Insert the

Tabs

tab on one end of

Strap

the chest strap into

 

 

the hole in one end

 

 

of the sensor as

 

 

shown. Then, press

 

 

the end of the sen-

 

Sensor

sor under the buckle

 

on the chest strap.

 

Tab

The tab should be

 

flush with the front

 

 

of the sensor.

 

 

The heart rate moni-

Sensor Buckle

tor must be worn

 

 

under your clothes,

 

 

tight against your

 

 

skin. Wrap the heart

 

 

rate monitor around

 

 

your chest in the lo-

 

 

cation shown. Make

 

 

sure that the logo is

 

 

right-side-up. Then,

 

 

attach the other end of the chest strap to the sensor. Adjust the length of the chest strap, if necessary.

Pull the sensor away from your body a few inches and locate the two electrode areas, which are covered by shallow ridges. Using saline solution such as saliva or contact lens solution, wet the electrode areas. Then, return the sensor to a position against your chest.

CARE AND MAINTENANCE

•Thoroughly dry the sensor with a soft towel after each use. Moisture may keep the sensor activated, shortening the life of the battery.

•Store the heart rate monitor in a warm, dry place.

Do not store the heart rate monitor in a plastic bag or other container that may trap moisture.

•Do not expose the heart rate monitor to direct sunlight for extended periods of time; do not expose it to temperatures above 122° F (50° C) or below 14° F (-10° C).

•Do not excessively bend or stretch the sensor when using or storing the heart rate monitor.

•To clean the sensor, use a damp cloth and a small amount of mild soap. Then, wipe the sensor with a damp cloth and thoroughly dry it with a soft towel.

Never use alcohol, abrasives, or chemicals to clean the sensor. Hand wash and air dry the chest strap.

TROUBLESHOOTING

If the heart rate monitor does not function properly, try the steps below.

•Make sure that you are wearing the heart rate moni- tor as described at the left. If the heart rate monitor does not function when positioned as described, move it slightly lower or higher on your chest.

•If heart rate readings are not displayed until you begin perspiring, rewet the electrode areas.

•For the console to display heart rate readings, you must be within arm’s length of the console.

•If there is a battery cover on the back of the sensor, replace the battery with a new battery of the same type.

•The heart rate monitor is designed to work with people who have normal heart rhythms. Heart rate reading problems may be caused by medical conditions such as premature ventricular contrac- tions (pvcs), tachycardia bursts, and arrhythmia.

•The operation of the heart rate monitor can be affected by magnetic interference from high power lines or other sources. If you suspect that magnetic interference is causing a problem, try relocating the fitness equipment.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model No. NTL19010.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page BEFORE YOU BEGIN Part Identification Chart Make sure that the power cord is unplugged AssemblySee the inset drawing. Tie the wire tie Screws, and then tighten them. Be careful Tie Pulse Wire Console Assembly Wire Tie 101 102 103 Console Base 87. Do not overtighten Screws Right Upright 77. Make sure that no wires areStar Washers 8. Note Start the lower Screw First Washers 8. Note Start the lower Screw first Upright 77. Make sure that no wires areScrews and then tighten them Percent. Then, unplug the power cordAttach the Right Inside Cover and the Right Care and Maintenance HOW to PUT on the Heart Rate MonitorTroubleshooting Chest Heart Rate MonitorHOW to Plug in the Power Cord Operation AND ADJUSTMENTFeatures of the Console DiagramConsole HOW to USE the Touch Screen HOW to Turn on the PowerConnect to your wireless network Check for firmware updates HOW to SET UP the CONSOLE Calibrate the incline system Create an iFit Live accountHOW to USE the Manual Mode Plug the power cord. Important If you do not When you are finished exercising, removeKey from the console Do this, the incline trainer’s electrical compoSelect an onboard workout HOW to USE AN Onboard WorkoutStart the workout Select the main menu. See on Select a set-a-goal workout HOW to USE a SET-A-GOAL WorkoutStart the workout. See on HOW to USE AN Ifit Live WorkoutHOW to USE the Equipment Settings Mode Exit the maintenance mode HOW to USE the Maintenance ModeCalibrate the incline system of the incline trainer Find KeycodesEnable Wi-Fi HOW to USE the Wireless Network ModeSet up and manage a wireless network connection Exit the wireless network modeHOW to USE the Internet Browser HOW to USE the Stereo Sound SystemHOW to Move the Incline Trainer Symptom The power turns off during use TroubleshootingSymptom The walking belt slows when walked on Page Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description Part ListDescription Exploded Drawing a Exploded Drawing B 106 110 Exploded Drawing D Exploded Drawing E Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents