Sears NTL19010.0 user manual

Page 30

SYMPTOM: The walking belt is off-center or slips when walked on

a.If the walking belt is off-center, first adjust incline to 40 percent. Remove the key and UNPLUG THE

POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the incline trainer for a few minutes. Repeat until the walking belt is centered.

a

b.If the walking belt slips when walked on, first adjust incline to 40 percent. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 3 to 4 in. (8 to 10 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and care- fully walk on the incline trainer for a few minutes. Repeat until the walking belt is properly tightened.

b

SYMPTOM: The iFit Live mode does not function correctly

a.If the iFit Live mode is not functioning correctly, make sure that the incline trainer has the most cur- rent firmware available (see step 3 on page 24).

SYMPTOM: The incline trainer will not connect to the wireless network

a.Make sure that the wireless settings on your con- sole are correct (see step 4 on page 25).

b.Make sure that the settings for your wireless net- work are correct.

c.If you still have questions, see the front cover of this manual.

30

Image 30
Contents QUESTIONS? Model No. NTL19010.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page BEFORE YOU BEGIN Part Identification Chart Assembly Make sure that the power cord is unpluggedSee the inset drawing. Tie the wire tie Screws, and then tighten them. Be careful Tie Pulse Wire Console Assembly Wire Tie 101 102 103 Right Upright 77. Make sure that no wires are Console Base 87. Do not overtighten ScrewsStar Washers 8. Note Start the lower Screw First Upright 77. Make sure that no wires are Washers 8. Note Start the lower Screw firstPercent. Then, unplug the power cord Screws and then tighten themAttach the Right Inside Cover and the Right Troubleshooting HOW to PUT on the Heart Rate MonitorCare and Maintenance Chest Heart Rate MonitorOperation AND ADJUSTMENT HOW to Plug in the Power CordDiagram Features of the ConsoleConsole HOW to Turn on the Power HOW to USE the Touch ScreenCalibrate the incline system HOW to SET UP the CONSOLE Connect to your wireless network Check for firmware updates Create an iFit Live accountHOW to USE the Manual Mode Key from the console When you are finished exercising, removePlug the power cord. Important If you do not Do this, the incline trainer’s electrical compoHOW to USE AN Onboard Workout Select an onboard workoutStart the workout HOW to USE a SET-A-GOAL Workout Select the main menu. See on Select a set-a-goal workoutHOW to USE AN Ifit Live Workout Start the workout. See onHOW to USE the Equipment Settings Mode Calibrate the incline system of the incline trainer HOW to USE the Maintenance ModeExit the maintenance mode Find KeycodesSet up and manage a wireless network connection HOW to USE the Wireless Network ModeEnable Wi-Fi Exit the wireless network modeHOW to USE the Stereo Sound System HOW to USE the Internet BrowserHOW to Move the Incline Trainer Troubleshooting Symptom The power turns off during useSymptom The walking belt slows when walked on Page Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Part List Qty DescriptionDescription Exploded Drawing a Exploded Drawing B 106 110 Exploded Drawing D Exploded Drawing E Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT