Sears NTL19010.0 HOW to USE the Maintenance Mode, Find Keycodes, Exit the maintenance mode

Page 24

HOW TO USE THE MAINTENANCE MODE

The console features a maintenance mode that al- lows you to update the console firmware, calibrate the incline of the incline trainer, calibrate the screen, view technical information, and view a button’s keycode.

1.Select the settings main menu. See step 1 on page 23.

2.Select the maintenance mode.

In the settings main menu, touch the Maintenance button to enter the mainte- nance mode.

The maintenance mode main screen will show information about the model and version of the in- cline trainer.

3.Update the console firmware.

For the best results, regularly check for firm- ware updates.

Touch the Firmware Update button to check for firmware updates using your wireless network. The update will begin automatically.

To avoid damaging the incline trainer, do not turn off the power or remove the key while the firmware is being updated.

Note: Occasionally, a firmware update may cause your console to function slightly differently. These updates are always designed to improve your exer- cise experience.

Note: If you cannot update the console firmware over your wireless network, you can update the firmware using a USB drive. Go to www.iFit.com and download the latest firmware update onto your

USB drive. Safely remove the USB drive from your computer and plug it into the USB port on the side of the console. The update should begin automatically.

The screen will show the progress of the update. When the update is complete, the incline trainer will turn off and then turn back on. If it does not, press the power switch into the off position. Wait for several seconds, and then press the power switch into the reset position. Note: It may take a few minutes for the console to be ready for use.

4.Calibrate the incline system of the incline trainer.

Touch the Calibrate Incline button. Then, touch the Begin button to calibrate the incline system. The in- cline trainer will automatically rise to the maximum incline level, lower to the minimum incline level, and then return to the starting position. This will calibrate the incline system. Press the Cancel but- ton to return to the maintenance mode. When the incline system is calibrated, touch the Finish button.

IMPORTANT: Keep pets, feet, and other objects away from the incline trainer while the incline system is calibrating. In an emergency, pull the key from the console to stop the incline calibration.

5.View machine information.

Touch the Machine Info button to view information about your incline trainer. After you view the infor- mation, touch the back button on the screen.

6.Find Keycodes.

This option is intended to be used by service tech- nicians to identify whether a certain button is work- ing correctly.

7.Exit the maintenance mode.

To exit the maintenance mode, press the back but- ton on the console.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents QUESTIONS? Model No. NTL19010.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page BEFORE YOU BEGIN Part Identification Chart Assembly Make sure that the power cord is unpluggedSee the inset drawing. Tie the wire tie Screws, and then tighten them. Be careful Tie Pulse Wire Console Assembly Wire Tie 101 102 103 Right Upright 77. Make sure that no wires are Console Base 87. Do not overtighten ScrewsStar Washers 8. Note Start the lower Screw First Upright 77. Make sure that no wires are Washers 8. Note Start the lower Screw firstPercent. Then, unplug the power cord Screws and then tighten themAttach the Right Inside Cover and the Right HOW to PUT on the Heart Rate Monitor Care and MaintenanceTroubleshooting Chest Heart Rate MonitorOperation AND ADJUSTMENT HOW to Plug in the Power CordDiagram Features of the ConsoleConsole HOW to Turn on the Power HOW to USE the Touch ScreenHOW to SET UP the CONSOLE  Connect to your wireless network Check for firmware updatesCalibrate the incline system Create an iFit Live accountHOW to USE the Manual Mode When you are finished exercising, remove Plug the power cord. Important If you do notKey from the console Do this, the incline trainer’s electrical compoHOW to USE AN Onboard Workout Select an onboard workoutStart the workout HOW to USE a SET-A-GOAL Workout Select the main menu. See on Select a set-a-goal workoutHOW to USE AN Ifit Live Workout Start the workout. See onHOW to USE the Equipment Settings Mode HOW to USE the Maintenance Mode Exit the maintenance modeCalibrate the incline system of the incline trainer Find KeycodesHOW to USE the Wireless Network Mode Enable Wi-FiSet up and manage a wireless network connection Exit the wireless network modeHOW to USE the Stereo Sound System HOW to USE the Internet BrowserHOW to Move the Incline Trainer Troubleshooting Symptom The power turns off during useSymptom The walking belt slows when walked on Page Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Part List Qty DescriptionDescription Exploded Drawing a Exploded Drawing B 106 110 Exploded Drawing D Exploded Drawing E Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents