Sears NTL19010.0 user manual Symptom The walking belt slows when walked on

Page 29

Locate the Reed Switch (55) and the Magnet (41) on the left side of the Pulley (42). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the #8 x 3/4" Clamp Screw (20), move the Reed Switch slightly, and then retighten the Screw. Reattach the Left Roller Cover (not shown) and run the incline trainer for a few minutes to check for a correct speed reading.

Top

View

1/8 in.

41

20

 

55

42

 

SYMPTOM: The incline of the incline trainer does not change correctly

a.Calibrate the incline system (see step 4 on page 24).

SYMPTOM: The walking belt slows when walked on

a.Use only a single-outlet surge suppressor that meets all of the specifications described on page 14.

b.If the walking belt is overtightened, incline trainer performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 3 to 4 in. (8 to 10 cm) off the walk- ing platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the incline trainer for a few minutes. Repeat until the walking belt is properly tightened.

b

3–4 in.

Idler Roller Screws

c.Your incline trainer features a walking belt coated with high-performance lubricant. IMPORTANT:

Never apply silicone spray or other substances to the walking belt or the walking platform un- less instructed to do so by an authorized ser- vice representative. Such substances may de- teriorate the walking belt and cause excessive wear. If you suspect that the walking belt needs more lubricant, see the front cover of this manual.

d.If the walking belt still slows when walked on, see the front cover of this manual.

29

Image 29
Contents Call TOLL-FREE QUESTIONS?Model No. NTL19010.0 Serial No Table of Contents Important Precautions Page BEFORE YOU BEGIN Part Identification Chart See the inset drawing. Tie the wire tie AssemblyMake sure that the power cord is unplugged Screws, and then tighten them. Be careful Tie Pulse Wire Console Assembly Wire Tie 101 102 103 Star Washers 8. Note Start the lower Screw First Right Upright 77. Make sure that no wires areConsole Base 87. Do not overtighten Screws Washers 8. Note Start the lower Screw first Upright 77. Make sure that no wires areAttach the Right Inside Cover and the Right Percent. Then, unplug the power cordScrews and then tighten them Care and Maintenance HOW to PUT on the Heart Rate MonitorTroubleshooting Chest Heart Rate MonitorHOW to Plug in the Power Cord Operation AND ADJUSTMENTConsole DiagramFeatures of the Console HOW to USE the Touch Screen HOW to Turn on the PowerConnect to your wireless network Check for firmware updates HOW to SET UP the CONSOLE Calibrate the incline system Create an iFit Live accountHOW to USE the Manual Mode Plug the power cord. Important If you do not When you are finished exercising, removeKey from the console Do this, the incline trainer’s electrical compoStart the workout HOW to USE AN Onboard WorkoutSelect an onboard workout Select the main menu. See on Select a set-a-goal workout HOW to USE a SET-A-GOAL WorkoutStart the workout. See on HOW to USE AN Ifit Live WorkoutHOW to USE the Equipment Settings Mode Exit the maintenance mode HOW to USE the Maintenance ModeCalibrate the incline system of the incline trainer Find KeycodesEnable Wi-Fi HOW to USE the Wireless Network ModeSet up and manage a wireless network connection Exit the wireless network modeHOW to USE the Internet Browser HOW to USE the Stereo Sound SystemHOW to Move the Incline Trainer Symptom The power turns off during use TroubleshootingSymptom The walking belt slows when walked on Page Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description Part ListDescription Exploded Drawing a Exploded Drawing B 106 110 Exploded Drawing D Exploded Drawing E Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty