JVC UX-F70MD manual Connecting Speakers, To connect an outdoor AM antenna, To attach spacers

Page 12

English

AM antenna

	1
	2	ANTENNA			Vinyl-covered wire
		ANTENNA			(not supplied)
			AM		(not supplied)
		AM	AM	EXT
		AM		EXT
			LOOP
		FM(75Ω)
		COAXIAL
				3
		AM loop antenna
		(supplied)

1If cords are covered with insulation, twist the core of the cord at the end of each cord, then remove the insulation.

2Connect the AM loop antenna to the AM LOOP terminals as illustrated.

3Turn the AM loop antenna until you have the best reception.

To connect an outdoor AM antenna

When reception is poor, connect a single vinyl-covered wire to the AM EXT terminal and extend it horizontally. The AM loop antenna must remain connected.

For better reception of both FM and AM

•Make sure the antenna conductors do not touch any other terminals and connecting cords.

•Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord.

Connecting Speakers

To attach spacers

If you want to place the speakers beside the main unit, it is recommended to leave a space (1 cm) between the main unit and the right speaker for ventilation.

It is recommended to attach the spacers (supplied) to the right speaker as the illustration below:

The main unit

The right speaker

Opening for ventilation

Spacers (supplied)

By peeling the cover seal from the spacers, you can attach them to the right speaker.

To remove the speaker grilles

The speaker grilles are removable as the illustration below.

Holes Projections

Speaker grille

To remove the speaker grille, insert your fingers at the top of the speaker grille, then pull towards you. Do the same at the bottom.

To attach the speaker grille, put the projections of the speaker grille into the holes of the speaker.

– 7 –

Image 12

Contents UX-F70MD UX-F72MD Page English Front view Class Laser Product Precautions IntroductionContents Location of the Buttons Main unitTop view Front viewMain Unit Display windowRemote Control Getting Started UnpackingTo connect an outdoor FM antenna FM antennaConnecting Speakers AM antennaTo connect an outdoor AM antenna To attach spacersConnecting Other Equipment To connect speakersTo connect another component such as analog audio equipment For playing the other equipment through this unitPutting the Batteries into the Remote Control To stop and cancel the display demonstration, pressTo start the display illumination manually, press Remote control Basic and Common OperationsMain unit Top view Main unit Front viewTurning On the Power Selecting the Sources and Starting PlayAdjusting the Volume Turning On/Off the Key-touch ToneReinforcing the Bass Sound Selecting the Sound ModesSetting the Display Illumination To adjust and register the colorTo select the color pattern To set TODAY’S ColorListening to FM and AM Broadcasts Setting the AM Tuner Interval Spacing Tuning in a StationPresetting Stations To change the FM reception modeTuning in a Preset Station Press the number buttons to select a preset numberOn the remote control only Press DISPLAY/CHARA Press SET againPlaying Back a CD MarkPrecautions on CD Playback Playing Back the Entire CD Normal PlayBasic CD Operations Program PlayTo check the program contents Playing at Random Random PlayTo modify the program Repeating Tracks Repeat Play Repeat ALL Repeat ONEPlaying Back an MD MarkAbout recording length mode Mdlp see Press MD open/close 0on the main unitInsert an MD into the MD loading slot Press MD 3Basic MD Operations Programing the Playing Order of the Tracks Program PlayTo change the informations on the display Playing Tracks in a Group Group Play To erase the entire program, press MD open/close 0toPress 4or ¢while pressing MD Group to select a group Searching by Title of the Track MD Title Search Playing Back a Tape To play both sides Reverse Mode Playing Back a TapeRecording on MDs Before You Start Recording on an MD About the track marksTo avoid erasing important recordings To put a track mark manually while recording anPrecautions for performing long-hour stereo recording Stereo Long-Hour Recording MdlpAbout High-Speed Recording To check the remaining recording timeRecording FM/AM Broadcasts Recording CD CD Synchronized RecordingBefore recording on an MD Recording Tape Tape Synchronized To record a single track during play or pauseTo check the remaining time while recording CD onto an MD To check the remaining time while recording tape onto an MDRecording Recording Speed Mode Press AUXStart playback on the external equipment Recording on Tapes To clean the heads, capstans, and pinch rollers Before You Start Recording on a TapeTo protect your recordings To keep the best recording and playback sound qualityRecording Reverse mode Mode 4/5 Mode 5/5Mode 8/15 Mode 1/2 Mode 2/2 Recording MD MD Synchronized RecordingRecording the External Equipment To check the clock time while recording MD onto a tapeRecording CD onto an MD and a Tape CD Synchronized Recording SpeedEditing MD Groups About MD GroupUsing MD Group Functions How to Make Up GroupsGuidance MD Group Functions Classifying the tracks on an MDIntroducing MD Group Editing Press Enter to finish the editing procedure Forming a Group Form GRDuring playback Press ¢or 4to select the last track of a new groupAdding a Track to a Group Entry GR Dividing a Group Divide GRPress SET During playback Press ¢or 4to select a track you want to add to a groupJoining Two Groups Join GR To join the divided groups, see the Join GR function toTo divide the joined group, see the Divide GR function on On the remote control only Press SET Press Enter to finish the editing procedureMoving a Group Move GR Ungrouping Tracks UngroupDissolving All Groups Ungr ALL Erasing Tracks in a Group Erase GREditing MD Tracks Introducing MD Track Editing Press = or +to adjust the dividing point precisely Dividing a Track DivideJoining Two Tracks Join Press ¢or 4to select a track you want to divideWhen the tracks belongs to a group Moving a Track MoveTo divide the joined tracks, see the Divide function on Press ¢or 4to select a track you want to moveErasing Tracks Erase Erasing All Tracks ALL EraseSelect a track you want to erase Press ¢or Press SET Repeat to select all the tracks you want to eraseAssigning Titles to an MD Press SET to enter the selected title entry mode Assigning the Disc Title, Track Title and Group TitleInsert an MD to edit Press MD Title INPUT/EDIT About the number of characters inputted for an MDChanging the Title Using the Timers Setting the Clock Using Recording TimerHow Recording Timer actually works Using Daily Timer How Daily Timer actually worksIf the unit is kept turned on when the timer-on time comes Daily Timer does not work at allUsing Sleep Timer Timer PriorityHow Sleep Timer actually works Maintenance Utoc User Table Of Contents Additional InformationMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Scms Serial Copy Management System Hcms High-speed Copy Management SystemMD/CD Messages Troubleshooting Track Protected X4 Speed Cannot Copy LOW TempSpecifications EN, CH