JVC UX-F70MD Setting the AM Tuner Interval Spacing, Tuning in a Station, Presetting Stations

Page 20

English

Setting the AM Tuner Interval Spacing

Some countries space AM stations 9 kHz apart, and some countries use 10 kHz spacing.

When shipped, the built-in AM tuner is set to 9 kHz spacing. You can change it to 9 kHz or 10 kHz spacing.

On the main unit ONLY:

To set the AM tuner to the 10 kHz spacing, be sure that the unit is turned off, but is plugged into a wall outlet.

While holding ¢, press STANDBY/ON. The unit turns on and “AM 10 kHz” appears on the display for a while.

To set it back to the 9 kHz spacing, be sure that the unit is turned off, but is plugged into a wall outlet.

While holding 4, press STANDBY/ON. The unit turns on and “AM 9 kHz” appears on the display for a while.

Tuning in a Station

1 Press FM/AM/AUX (or FM/AM on the main unit) repeatedly to select “FM” or “AM.”

The unit automatically turns on with the last source selected.

•Each time you press the button, the source changes as follows:

When using the

When using the

remote control:

main unit:

FM

 

 

AM

 

 

 

(TUNER)

FM

 

AM

 

AUX

(TUNER)

 

 

 

 

2 Press and hold ¢or 4until the station

 

frequencies start changing continuously on the display.

•¢: to increase the frequencies.

•4: to decrease the frequencies.

The unit starts searching stations and stops when a station of sufficient signal strength is tuned in.

Ex. An FM station is tuned in.

•If an FM program is broadcast in stereo, the ST (stereo) indicator lights on the display.

To stop during searching, press ¢or 4.

When you repeatedly press ¢or 4

The frequency changes step by step.

To change the FM reception mode

When an FM stereo broadcast is noisy or hard to receive, you can change the FM reception mode to improve the reception.

On the remote control ONLY:

Press FM MODE so that the MONO indicator lights on the display.

•Each time you press the button, MONO indicator lights and goes off alternately.

When the MONO indicator is lit:

Reception improves though stereo effect is lost.

When the MONO indicator is not lit:

You can hear stereo sound when a program is broadcast in stereo.

The ST indicator lights while receiving the FM stereo broadcast.

In addition, static noise between stations will be erased while tuning.

Presetting Stations

You can preset 30 FM and 15 AM stations manually.

In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

On the remote control ONLY:

1 Tune in a station you want to preset.

• See “Tuning in a Station” to the left.

2 Press SET.

The preset number starts flashing as follows:

•When you select an FM station in step 1

•When you select an AM station in step 1

Preset No. 1 alway appears at first.

– 15 –

Page 19 Page 21
Image 20
Page 19 Page 21
Contents UX-F70MD UX-F72MD Page English Front view Class Laser Product Precautions IntroductionContents Location of the Buttons Main unitTop view Front viewMain Unit Display windowRemote Control Getting Started UnpackingTo connect an outdoor FM antenna FM antennaConnecting Speakers AM antennaTo connect an outdoor AM antenna To attach spacersConnecting Other Equipment To connect speakersTo connect another component such as analog audio equipment For playing the other equipment through this unitTo start the display illumination manually, press Putting the Batteries into the Remote ControlTo stop and cancel the display demonstration, press Remote control Basic and Common OperationsMain unit Top view Main unit Front viewTurning On the Power Selecting the Sources and Starting PlayAdjusting the Volume Turning On/Off the Key-touch ToneReinforcing the Bass Sound Selecting the Sound ModesSetting the Display Illumination To adjust and register the colorTo select the color pattern To set TODAY’S ColorListening to FM and AM Broadcasts Setting the AM Tuner Interval Spacing Tuning in a StationPresetting Stations To change the FM reception modeTuning in a Preset Station Press the number buttons to select a preset numberOn the remote control only Press DISPLAY/CHARA Press SET againPlaying Back a CD MarkPrecautions on CD Playback Playing Back the Entire CD Normal PlayBasic CD Operations Program PlayTo modify the program To check the program contentsPlaying at Random Random Play Repeating Tracks Repeat Play Repeat ALL Repeat ONEPlaying Back an MD MarkAbout recording length mode Mdlp see Press MD open/close 0on the main unitInsert an MD into the MD loading slot Press MD 3To change the informations on the display Basic MD OperationsPrograming the Playing Order of the Tracks Program Play Press 4or ¢while pressing MD Group to select a group Playing Tracks in a Group Group PlayTo erase the entire program, press MD open/close 0to Searching by Title of the Track MD Title Search Playing Back a Tape To play both sides Reverse Mode Playing Back a TapeRecording on MDs Before You Start Recording on an MD About the track marksTo avoid erasing important recordings To put a track mark manually while recording anPrecautions for performing long-hour stereo recording Stereo Long-Hour Recording MdlpAbout High-Speed Recording To check the remaining recording timeBefore recording on an MD Recording FM/AM BroadcastsRecording CD CD Synchronized Recording Recording Tape Tape Synchronized To record a single track during play or pauseTo check the remaining time while recording CD onto an MD To check the remaining time while recording tape onto an MDStart playback on the external equipment Recording Recording Speed ModePress AUX Recording on Tapes To clean the heads, capstans, and pinch rollers Before You Start Recording on a TapeTo protect your recordings To keep the best recording and playback sound qualityMode 8/15 Recording Reverse modeMode 4/5 Mode 5/5 Mode 1/2 Mode 2/2 Recording MD MD Synchronized RecordingRecording the External Equipment To check the clock time while recording MD onto a tapeRecording CD onto an MD and a Tape CD Synchronized Recording SpeedEditing MD Groups About MD GroupUsing MD Group Functions How to Make Up GroupsGuidance MD Group Functions Classifying the tracks on an MDIntroducing MD Group Editing Press Enter to finish the editing procedure Forming a Group Form GRDuring playback Press ¢or 4to select the last track of a new groupAdding a Track to a Group Entry GR Dividing a Group Divide GRPress SET During playback Press ¢or 4to select a track you want to add to a groupTo divide the joined group, see the Divide GR function on Joining Two Groups Join GRTo join the divided groups, see the Join GR function to On the remote control only Press SET Press Enter to finish the editing procedureMoving a Group Move GR Ungrouping Tracks UngroupDissolving All Groups Ungr ALL Erasing Tracks in a Group Erase GREditing MD Tracks Introducing MD Track Editing Press = or +to adjust the dividing point precisely Dividing a Track DivideJoining Two Tracks Join Press ¢or 4to select a track you want to divideWhen the tracks belongs to a group Moving a Track MoveTo divide the joined tracks, see the Divide function on Press ¢or 4to select a track you want to moveErasing Tracks Erase Erasing All Tracks ALL EraseSelect a track you want to erase Press ¢or Press SET Repeat to select all the tracks you want to eraseAssigning Titles to an MD Press SET to enter the selected title entry mode Assigning the Disc Title, Track Title and Group TitleInsert an MD to edit Press MD Title INPUT/EDIT About the number of characters inputted for an MDChanging the Title Using the Timers How Recording Timer actually works Setting the ClockUsing Recording Timer Using Daily Timer How Daily Timer actually worksIf the unit is kept turned on when the timer-on time comes Daily Timer does not work at allHow Sleep Timer actually works Using Sleep TimerTimer Priority Maintenance Utoc User Table Of Contents Additional InformationMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Scms Serial Copy Management System Hcms High-speed Copy Management SystemMD/CD Messages Troubleshooting Track Protected X4 Speed Cannot Copy LOW TempSpecifications EN, CH
Top Page Image Contents