JVC UX-F72MD, UX-F70MD manual Connecting Other Equipment, To connect speakers

Page 13

Continued

English

To connect speakers

You can connect the speakers by following the procedure

	below.
	1
	2	Speaker terminals		3,4
		SPEAKER IMPEDANCE		Red
			MIN 4Ω
	Speaker cord	+	+	Speaker cord
		R	L	Speaker cord


		–	–
			Black
		R		L
	Rear of the right		Rear of the left
	speaker		speaker

1If cords are covered with insulation, twist the core of the cord at the end of each cord, then remove the insulation.

2Open the speaker terminal.

3Insert the end of the speaker cord to the terminal. Match the polarity: White cord to red (+) terminal and black cord to black (–) terminal.

4Close the speaker terminal on the rear of the unit.

Use only speakers with the speaker impedance — 4 Ω to

16Ω.

Connecting Other Equipment

You can connect the following equipment which can be used as a playback device.

When you connect and use the equipment, refer also to its manual supplied.

• DO NOT connect other equipment while the power is on.

•DO NOT plug in any equipment until all connections are complete.

To connect another component such as analog audio equipment

Be sure that the plugs of the audio cords and the jacks on the rear of the unit are color-coded: White plugs and jacks are for left audio signals, and red ones for right audio signals.

	LINE IN
	(AUX)
R	L
SPEAKER IMPEDANCE
MIN 4
R	L
AC IN
Ex. Analog audio
equipment
	To output

For playing the other equipment through this unit,

connect between the audio output jacks on the other equipment and LINE IN (AUX) jacks by using audio cords (not supplied.)

– 8 –

Image 13

Contents UX-F70MD UX-F72MD Page English Front view Class Laser Product Introduction PrecautionsContents Main unit Location of the ButtonsTop view Front viewDisplay window Main UnitRemote Control Unpacking Getting StartedTo connect an outdoor FM antenna FM antennaAM antenna Connecting SpeakersTo connect an outdoor AM antenna To attach spacersTo connect speakers Connecting Other EquipmentTo connect another component such as analog audio equipment For playing the other equipment through this unitTo stop and cancel the display demonstration, press Putting the Batteries into the Remote ControlTo start the display illumination manually, press Basic and Common Operations Remote controlMain unit Top view Main unit Front viewSelecting the Sources and Starting Play Turning On the PowerTurning On/Off the Key-touch Tone Adjusting the VolumeReinforcing the Bass Sound Selecting the Sound ModesTo adjust and register the color Setting the Display IlluminationTo select the color pattern To set TODAY’S ColorListening to FM and AM Broadcasts Tuning in a Station Setting the AM Tuner Interval SpacingPresetting Stations To change the FM reception modePress the number buttons to select a preset number Tuning in a Preset StationOn the remote control only Press DISPLAY/CHARA Press SET againMark Playing Back a CDPlaying Back the Entire CD Normal Play Precautions on CD PlaybackProgram Play Basic CD OperationsPlaying at Random Random Play To check the program contentsTo modify the program Repeat ALL Repeat ONE Repeating Tracks Repeat PlayMark Playing Back an MDPress MD open/close 0on the main unit About recording length mode Mdlp seeInsert an MD into the MD loading slot Press MD 3Programing the Playing Order of the Tracks Program Play Basic MD OperationsTo change the informations on the display To erase the entire program, press MD open/close 0to Playing Tracks in a Group Group PlayPress 4or ¢while pressing MD Group to select a group Searching by Title of the Track MD Title Search Playing Back a Tape Playing Back a Tape To play both sides Reverse ModeRecording on MDs About the track marks Before You Start Recording on an MDTo avoid erasing important recordings To put a track mark manually while recording anStereo Long-Hour Recording Mdlp Precautions for performing long-hour stereo recordingAbout High-Speed Recording To check the remaining recording timeRecording CD CD Synchronized Recording Recording FM/AM BroadcastsBefore recording on an MD To record a single track during play or pause Recording Tape Tape SynchronizedTo check the remaining time while recording CD onto an MD To check the remaining time while recording tape onto an MDPress AUX Recording Recording Speed ModeStart playback on the external equipment Recording on Tapes Before You Start Recording on a Tape To clean the heads, capstans, and pinch rollersTo protect your recordings To keep the best recording and playback sound qualityMode 4/5 Mode 5/5 Recording Reverse modeMode 8/15 Recording MD MD Synchronized Recording Mode 1/2 Mode 2/2Recording the External Equipment To check the clock time while recording MD onto a tapeSpeed Recording CD onto an MD and a Tape CD Synchronized RecordingAbout MD Group Editing MD GroupsHow to Make Up Groups Using MD Group FunctionsGuidance MD Group Functions Classifying the tracks on an MDIntroducing MD Group Editing Forming a Group Form GR Press Enter to finish the editing procedureDuring playback Press ¢or 4to select the last track of a new groupDividing a Group Divide GR Adding a Track to a Group Entry GRPress SET During playback Press ¢or 4to select a track you want to add to a groupTo join the divided groups, see the Join GR function to Joining Two Groups Join GRTo divide the joined group, see the Divide GR function on Press Enter to finish the editing procedure On the remote control only Press SETMoving a Group Move GR Ungrouping Tracks UngroupErasing Tracks in a Group Erase GR Dissolving All Groups Ungr ALLEditing MD Tracks Introducing MD Track Editing Dividing a Track Divide Press = or +to adjust the dividing point preciselyJoining Two Tracks Join Press ¢or 4to select a track you want to divideMoving a Track Move When the tracks belongs to a groupTo divide the joined tracks, see the Divide function on Press ¢or 4to select a track you want to moveErasing All Tracks ALL Erase Erasing Tracks EraseSelect a track you want to erase Press ¢or Press SET Repeat to select all the tracks you want to eraseAssigning Titles to an MD Assigning the Disc Title, Track Title and Group Title Press SET to enter the selected title entry modeInsert an MD to edit Press MD Title INPUT/EDIT About the number of characters inputted for an MDChanging the Title Using the Timers Using Recording Timer Setting the ClockHow Recording Timer actually works How Daily Timer actually works Using Daily TimerDaily Timer does not work at all If the unit is kept turned on when the timer-on time comesTimer Priority Using Sleep TimerHow Sleep Timer actually works Maintenance Additional Information Utoc User Table Of ContentsMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Hcms High-speed Copy Management System Scms Serial Copy Management SystemMD/CD Messages Track Protected X4 Speed Cannot Copy LOW Temp TroubleshootingSpecifications EN, CH