JVC UX-F72MD, UX-F70MD manual Playing Back a Tape, To play both sides Reverse Mode

Page 33

Playing Back a Tape

You can play back type I, II, and IV tapes.

1 Press TAPE EJECT 0.

The cassette holder opens.

Cassette holder

To stop during play, press 7.

To fast-wind to the left or to the right, press 4or ¢.

To remove the cassette, press TAPE EJECT 0.

DO NOT press TAPE EJECT 0 during tape play.

English

EJECT

TAPE

2 Put a cassette in with the exposed part of the tape in front.

Cassette holder

To play both sides — Reverse Mode

You can set the deck to play just one side of a tape, both sides once, or both sides continuously.

On the remote control ONLY:

Press REV. MODE.

•Each time you press the button, the reverse mode changes as follows:

: To only play back one side (front or reverse).

: To play back the front and reverse sides once.

: To play back both front and reverse sides continuously.

	To check the clock time while playing back a tape
A	On the remote control ONLY:
	Press DISPLAY/CHARA.
EJECT	• Each time you press the button, the source indications
TAPE	• Each time you press the button, the source indications
	and the clock time alternate on the display.

3 Close the cassette holder gently.

4 Press TAPE 23.

The unit automatically turns on and the tape play starts.

•Each time you press the button, the tape direction changes as follows:

:plays the front side.

:plays the reverse side.

Tape indicator

Reverse mode

Tape direction

When the tape plays to the end, the deck automatically

stops if the reverse mode is set to or . (See “To play both sides — Reverse Mode” to the right.)

The use of the C-120 or thinner tape is not recommended, since characteristic deterioration may occur and this tape easily jams in the pinchrollers and the capstans.

– 28 –

Image 33

Contents UX-F70MD UX-F72MD Page English Front view Class Laser Product Introduction PrecautionsContents Main unit Location of the ButtonsTop view Front viewDisplay window Main UnitRemote Control Unpacking Getting StartedTo connect an outdoor FM antenna FM antennaAM antenna Connecting SpeakersTo connect an outdoor AM antenna To attach spacersTo connect speakers Connecting Other EquipmentTo connect another component such as analog audio equipment For playing the other equipment through this unitPutting the Batteries into the Remote Control To stop and cancel the display demonstration, pressTo start the display illumination manually, press Basic and Common Operations Remote controlMain unit Top view Main unit Front viewSelecting the Sources and Starting Play Turning On the PowerTurning On/Off the Key-touch Tone Adjusting the VolumeReinforcing the Bass Sound Selecting the Sound ModesTo adjust and register the color Setting the Display IlluminationTo select the color pattern To set TODAY’S ColorListening to FM and AM Broadcasts Tuning in a Station Setting the AM Tuner Interval SpacingPresetting Stations To change the FM reception modePress the number buttons to select a preset number Tuning in a Preset StationOn the remote control only Press DISPLAY/CHARA Press SET againMark Playing Back a CDPlaying Back the Entire CD Normal Play Precautions on CD PlaybackProgram Play Basic CD OperationsTo check the program contents Playing at Random Random PlayTo modify the program Repeat ALL Repeat ONE Repeating Tracks Repeat PlayMark Playing Back an MDPress MD open/close 0on the main unit About recording length mode Mdlp seeInsert an MD into the MD loading slot Press MD 3Basic MD Operations Programing the Playing Order of the Tracks Program PlayTo change the informations on the display Playing Tracks in a Group Group Play To erase the entire program, press MD open/close 0toPress 4or ¢while pressing MD Group to select a group Searching by Title of the Track MD Title Search Playing Back a Tape Playing Back a Tape To play both sides Reverse ModeRecording on MDs About the track marks Before You Start Recording on an MDTo avoid erasing important recordings To put a track mark manually while recording anStereo Long-Hour Recording Mdlp Precautions for performing long-hour stereo recordingAbout High-Speed Recording To check the remaining recording timeRecording FM/AM Broadcasts Recording CD CD Synchronized RecordingBefore recording on an MD To record a single track during play or pause Recording Tape Tape SynchronizedTo check the remaining time while recording CD onto an MD To check the remaining time while recording tape onto an MDRecording Recording Speed Mode Press AUXStart playback on the external equipment Recording on Tapes Before You Start Recording on a Tape To clean the heads, capstans, and pinch rollersTo protect your recordings To keep the best recording and playback sound qualityRecording Reverse mode Mode 4/5 Mode 5/5Mode 8/15 Recording MD MD Synchronized Recording Mode 1/2 Mode 2/2Recording the External Equipment To check the clock time while recording MD onto a tapeSpeed Recording CD onto an MD and a Tape CD Synchronized RecordingAbout MD Group Editing MD GroupsHow to Make Up Groups Using MD Group FunctionsGuidance MD Group Functions Classifying the tracks on an MDIntroducing MD Group Editing Forming a Group Form GR Press Enter to finish the editing procedureDuring playback Press ¢or 4to select the last track of a new groupDividing a Group Divide GR Adding a Track to a Group Entry GRPress SET During playback Press ¢or 4to select a track you want to add to a groupJoining Two Groups Join GR To join the divided groups, see the Join GR function toTo divide the joined group, see the Divide GR function on Press Enter to finish the editing procedure On the remote control only Press SETMoving a Group Move GR Ungrouping Tracks UngroupErasing Tracks in a Group Erase GR Dissolving All Groups Ungr ALLEditing MD Tracks Introducing MD Track Editing Dividing a Track Divide Press = or +to adjust the dividing point preciselyJoining Two Tracks Join Press ¢or 4to select a track you want to divideMoving a Track Move When the tracks belongs to a groupTo divide the joined tracks, see the Divide function on Press ¢or 4to select a track you want to moveErasing All Tracks ALL Erase Erasing Tracks EraseSelect a track you want to erase Press ¢or Press SET Repeat to select all the tracks you want to eraseAssigning Titles to an MD Assigning the Disc Title, Track Title and Group Title Press SET to enter the selected title entry modeInsert an MD to edit Press MD Title INPUT/EDIT About the number of characters inputted for an MDChanging the Title Using the Timers Setting the Clock Using Recording TimerHow Recording Timer actually works How Daily Timer actually works Using Daily TimerDaily Timer does not work at all If the unit is kept turned on when the timer-on time comesUsing Sleep Timer Timer PriorityHow Sleep Timer actually works Maintenance Additional Information Utoc User Table Of ContentsMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Hcms High-speed Copy Management System Scms Serial Copy Management SystemMD/CD Messages Track Protected X4 Speed Cannot Copy LOW Temp TroubleshootingSpecifications EN, CH