Gold's Gym GGTL04607.1 manual Bolts, Front View Side View View from Above

Page 10

9.While another person holds the Console Base (26) near the right Handrail (18), attach the ground wire on the Console Base to the right Handrail with a #8 x 1/2" Ground Screw (11).

Connect the wire harness on the Console Base (26) to the Upright Wire (28). See the inset drawing. The connectors should slide to- gether easily and snap into place. If they do not, turn one connector and try again. IF THE

CONNECTORS ARE NOT CONNECTED PROP- ERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

10. Insert the wires into the Console Base (26) as you set the Console Base on the Handrails. Be careful not to pinch the wires. Next, thread two 1/4" x 1/2" Bolts (22) with 1/4" Star Washers (21) into the Handrails and the Console Base; do not tighten the Bolts yet.

Attach the Console Base (26) to the Handrails (18) with four #8 x 3/4" Screws (2). Then, tighten the two 1/4" x 1/2" Bolts (22).

11. Lower the Uprights (31, 36).

See the inset drawing. Position the Uprights (31, 36) so that the Frame (74) is centered be- tween the Uprights.

Firmly tighten the 3/8" x 3" Bolts (32) and then the 3/8" x 2 1/4" Bolts (40) on each side of the treadmill. Do not overtighten the 3/8" x 3"

Bolts.

9		26
Wire	11	Ground
Wire		Wire
Harness	28
	28	18
		18
		28

	10	26	Front View
	18	26	Front View		18
	18				18
	2	21		2	21
	2	22		2	21
					22
	11		Side View		32
					40
			74	31, 36
			74

31	View from Above	36
	74

10

Image 10

Contents QUESTIONS? Model No. GGTL04607.1 Serial NoTable of Contents Use Important PrecautionsWhen connecting the power cord see Pulse sensor is not a medical devicePage Before YOU Begin Assembly Tighten the Bolts yet Fully tighten the Bolts yetDo not overtighten the Bolts the Wheels Should turn freely Outer side of the Frame Spacer facing See the left inset drawing. Identify the twoFully tighten the Bolt yet Upright Wire Bolts Front View Side View View from AboveMake sure that no wires are pinched. Reattach HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleFollow your progress with the display Measure your heart rate if desiredSelect one of the heart rate workouts Enter your weight if desired HOW to USE AN Event Training WorkoutSelect an event training workout. To select an Select a weight loss workout. To select a HOW to USE a Weight Loss WorkoutEnter your weight Press the Start button to start the workoutHOW to USE a Classic Workout Select one of the classic workouts. To select oneHOW to USE the Stereo Sound System Information ModeOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Key and Unplug the Power CORD. Using View Problem The walking belt slows when walked onUnplug the Power CORD. If the walking TopWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Key No. Qty Description R0608AQty Description Exploded Drawing A-Model No. GGTL04607.1 R0608A Exploded Drawing B-Model No. GGTL04607.1 R0608A Exploded Drawing C-Model No. GGTL04607.1 R0608A Exploded Drawing D-Model No. GGTL04607.1 R0608A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT