Gold's Gym GGTL04607.1 manual Assembly

Page 6

ASSEMBLY

To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480. Assembly re- quires two persons. Set the treadmill in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, lubricant may be transferred to the top of the walking belt or to the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lu- bricant on top of the walking belt, wipe it off with a soft cloth and mild, non-abrasive cleaner.

Assembly requires the included hex keys

and your own Phillips screwdriver

, rubber

.

mallet

, adjustable wrench

, wire cutters

, and needlenose pliers

Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached to one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assem- bly. Extra hardware may be included.

1/4" x 1/2"

#10 x 1" Tek

#8 x 3/4"

Wheel Spacer

1/4" Star Washer

Bolt (22)–2

Screw (27)–2

Tek Screw (38)–4

(44)–4

(21)–2

5/16" x 2 1/4" Bolt (20)–4

#8 x 3/4" Screw (2)–4

3/8" Flat Washer

5/16" Star

 

 

 

 

 

#8 x 1/2" Ground

Washer (19)–4

3/8" x 2 1/4" Bolt (40)–4

(33)–2

 

Screw (11)–2

 

 

 

3/8" x 3" Bolt (32)–4

 

3/8" Locknut

3/8" Star Washer

 

 

(47)–4

(7)–4

1.Orient the Base (48) as shown. Attach the four Base Pads (37) to the Base with four #8 x 3/4" Tek Screws (38).

1

 

37

38

 

 

 

38

 

48

 

37

 

 

38

 

 

 

 

 

 

 

38

37

 

 

 

37

 

 

 

 

 

 

6

 

 

 

 

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents QUESTIONS? Model No. GGTL04607.1 Serial NoTable of Contents Use Important PrecautionsWhen connecting the power cord see Pulse sensor is not a medical devicePage Before YOU Begin Assembly Fully tighten the Bolts yet Tighten the Bolts yetDo not overtighten the Bolts the Wheels Should turn freely See the left inset drawing. Identify the two Outer side of the Frame Spacer facingFully tighten the Bolt yet Upright Wire Bolts Front View Side View View from AboveMake sure that no wires are pinched. Reattach Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleFollow your progress with the display Measure your heart rate if desiredSelect one of the heart rate workouts HOW to USE AN Event Training Workout Enter your weight if desiredSelect an event training workout. To select an Select a weight loss workout. To select a HOW to USE a Weight Loss WorkoutEnter your weight Press the Start button to start the workoutHOW to USE a Classic Workout Select one of the classic workouts. To select oneInformation Mode HOW to USE the Stereo Sound SystemOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Key and Unplug the Power CORD. Using View Problem The walking belt slows when walked onUnplug the Power CORD. If the walking TopWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R0608A Key No. Qty DescriptionQty Description Exploded Drawing A-Model No. GGTL04607.1 R0608A Exploded Drawing B-Model No. GGTL04607.1 R0608A Exploded Drawing C-Model No. GGTL04607.1 R0608A Exploded Drawing D-Model No. GGTL04607.1 R0608A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents