Gold's Gym GGTL04607.1 manual Troubleshooting, Compatible with GFCI-equipped outlets

Page 23

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 12. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has tripped.

 

 

To reset the circuit breaker, wait for five minutes

Tripped

Reset

and then press the switch back in.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 20 to turn off the demo mode.

 

 

 

PROBLEM: The displays of the console do not function properly

 

 

 

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

 

 

2

POWER CORD. Remove the two #12 x 1 1/4"

4

 

Screws (4) and the two #8 x 3/4" Screws (2) and

 

 

4

carefully remove the Hood (1).

 

 

1

 

 

 

 

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model No. GGTL04607.1 Serial No QUESTIONS?Table of Contents Pulse sensor is not a medical device Important PrecautionsWhen connecting the power cord see UsePage Before YOU Begin Assembly Do not overtighten the Bolts the Wheels Should turn freely Fully tighten the Bolts yetTighten the Bolts yet Fully tighten the Bolt yet See the left inset drawing. Identify the twoOuter side of the Frame Spacer facing Upright Wire Front View Side View View from Above BoltsMake sure that no wires are pinched. Reattach PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeMeasure your heart rate if desired Follow your progress with the displaySelect one of the heart rate workouts Select an event training workout. To select an HOW to USE AN Event Training WorkoutEnter your weight if desired Press the Start button to start the workout HOW to USE a Weight Loss WorkoutEnter your weight Select a weight loss workout. To select aSelect one of the classic workouts. To select one HOW to USE a Classic WorkoutOptional Chest Pulse Sensor Information ModeHOW to USE the Stereo Sound System HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Compatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Top View Problem The walking belt slows when walked onUnplug the Power CORD. If the walking Key and Unplug the Power CORD. UsingExercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Qty Description R0608AKey No. Qty Description Exploded Drawing A-Model No. GGTL04607.1 R0608A Exploded Drawing B-Model No. GGTL04607.1 R0608A Exploded Drawing C-Model No. GGTL04607.1 R0608A Exploded Drawing D-Model No. GGTL04607.1 R0608A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents