PART | R0102A |
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key No. | Qty. | Description | Key No. | Qty. | Description |
1 | 1 | Allen Wrench | 52 | 1 | Incline Motor Bolt (Top) |
2 | 2 | Wheel Bolt | 53 | 8 | Endcap Washer |
3 | 1 | Rear Endcap (Left) | 54 | 1 | Incline Motor Stop |
4 | 2 | Roller Adj. Washer | 55 | 8 | Endcap Nut |
5 | 2 | Rear Roller Adj. Washer | 56 | 1 | Incline Motor Bolt (Bottom) |
6 | 2 | Rear Wheel | 57 | 1 | Incline Motor |
7 | 8 | Front Wheel Nut/Frame Pivot Nut | 58 | 1 | Front Roller Bolt |
8 | 8 | Endcap Screw | 59 | 4 | Plastic |
9 | 1 | Roller Guard (Left) | 60 | 1 | Electronic Plate |
10 | 1 | Roller Guard (Right) | 61 | 1 | Controller |
11 | 1 | Rear Endcap (Right) | 62 | 1 | Motor Controller Wire |
12 | 1 | Roller Ground Wire | 63 | 1 | Power Cord |
13 | 1 | Filter Wire | 64 | 1 | Power Cord Grommet |
14 | 1 | Rear Roller | 65 | 1 | On/Off Switch |
15 | 1 | Warning Decal | 66 | 2 | Belly Pan Screw (Long) |
16 | 1 | Latch Plate | 67 | 1 | Audio Wire Nut |
17 | 2 | Latch Plate Screw | 68 | 1 | Circuit Breaker |
18 | 2 | Frame Pivot Bolt | 69 | 2 | Static Decal |
19 | 1 | Front Endcap (Left) | 70 | 1 | 12” Audio Wire |
20 | 2 | Belt Guide | 71 | 1 | Belly Pan |
21 | 1 | Foot Grip (Left) | 72 | 4 | 3/4” Screw |
22 | 1 | Walking Belt | 73** | 1 | Chest Pulse Sensor |
23 | 1 | Walking Deck | 74** | 1 | Chest Pulse Strap |
24 | 1 | Foot Grip (Right) | 75 | 3 | Base Pad |
25 | 1 | Power Board | 76 | 1 | Console Base |
26 | 1 | Front Endcap (Right) | 77 | 1 | Book Holder |
27 | 2 | Support Bracket Screw | 78 | 1 | Console |
28 | 1 | Support Bracket | 79 | 2 | Handrail Endcap |
29 | 1 | Front Roller/Pulley | 80 | 2 | Pulse Grip |
30 | 1 | Magnet | 81 | 4 | Pulse Grip Screw |
31 | 8 | Console Screw (Long) | 82 | 4 | Console Screw (Short) |
32 | 2 | Washer | 83 | 1 | Console Back |
33 | 2 | Frame Pivot Bushing | 84* | 2 | Extension Leg Assembly |
34 | 2 | Frame Pivot Spacer | 85 | 2 | Extension Leg Endcap |
35 | 1 | Reed Switch | 86 | 12 | Base Screw/Latch Screw |
36 | 1 | Reed Switch Clip | 87 | 2 | Incline Motor Spacer |
37 | 1 | iFIT.com Wire | 88 | 2 | Extension Leg |
38* | 1 | Motor Assembly | 89 | 1 | Handrail |
39 | 1 | Flywheel/Pulley | 90 | 4 | Thick Base Pad |
40 | 1 | Motor Belt | 91 | 1 | Motor Hood |
41 | 1 | Motor Pivot Nut | 92 | 1 | 8” Wire Tie |
42 | 3 | Motor Tension Nut/Lift Frame Nut | 93 | 2 | Cable Tie Clamp |
43 | 1 | Motor Tension Washer | 94 | 1 | Transformer |
44** | 2 | Optional Weights | 95 | 1 | Releasable Tie |
45 | 1 | Motor Pivot Bolt | 96 | 2 | Lift Pivot Bolt |
46 | 1 | Motor | 97 | 2 | Front Wheel Bolt |
47 | 1 | Lift Frame | 98 | 2 | Front Wheel |
48 | 1 | Motor Star Washer | 99 | 1 | Incline Motor Guard |
49 | 10 | Screw | 100 | 1 | Upright Grommet |
50 | 1 | Jack | 101 | 1 | Upright Wire Harness |
51 | 1 | Key/Clip | 102** | 2 | Hand Weight |
30