Healthrider 831.299301 manual TROUBLE-SHOOTING and Maintenance, Problem, Solution

Page 22

TROUBLE-SHOOTING AND MAINTENANCE

Most treadmill problems can be solved by following the instructions below, if further assistance is needed, please call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).

PROBLEM

1.The power does not turn on

SOLUTION

a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC an d 15 amps.

b. Make sure that the key is fully inserted into the console.

C, Check the circuit breaker located on the frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d.Check the on/off switch located on the frame near the power cord. The switch must be in the on posi- tion.

Tripped Reset

I PositionOn

2.The power turns off during use

3.The walking belt slows when walked

on

a. Check the cimuit breaker located on the treadmill frame near the power cord (see

1.c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the p(_wer cord is plugged in.

c.Remove the key from the console and then reinsert it.

d.Make sure that the on/off switch is in the on position (see 1. d. above).

a. Make sure that only an appropriate surge suppressor is used (see 1. a. above).

b.If the walking belt is overtightened, tread- mill performance may decrease and the walking belt may be permanently dam- aged. Remove the key and UNPLUG THE POWER CORD. Using the included allen

wrench, turn both rear roller adjustment bolts counterclockwise 1/4 of a turn. When

the walking belt is properly tightened, you

should be able

to lift the edges of the

Rear Roller Adjustment

Bolts

walking belt 3

to 4 inches off the walking

 

platform. Be careful to keep the walking

 

belt centered.

Plug in the power

cord,

insert the key and run the treadmill

for a few

minutes. Repeat until the walking

belt

is properly tightened.

 

22

Image 22
Contents Hoffman ESTATES, IL Contents Important Precautions Whileoperatingor Right Side Before YOU BeginBack Assembly Performant Lube Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Grounding P Grounded Outlet 3rounding PlugConsole, remove it Diagram of the ConsoleFeatures of the Console Incline of the treadmill as a personal trainer guidesDescriptionoftheconsole Select the manual mode HOW to Turn on the PowerPlug in the power cord see HOW to Plug in the Power Cord on ElAdjust the incline of the treadmillOn/off switch near the power cord to the off Tons, and adjust the incline of the treadmill to 1.5%Incline must be at 1.5% when the treadmill Optional chest pulseLlUse the hand weights, if desired Select one of the four preset programsFollow your progress with the four displays Calories Refer to on HOW to Connect Your Portable CD Player HOW to Connect Your Portable StereoYour computer HOW to Connect Your ComputerNOW to Connect Your Home Stereo AdapterHOW to Connect Your VCR ChangePage Directly from Next settings of the programUSE Programs OUR !ERNOptional Handgrip Pulse Sensor Information Modfjdemo Mode Optional Chest Pulse SensorDisplay will show the total Tended to be used onlyHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEProblem TROUBLE-SHOOTING and MaintenanceSolution Walking belt is off-center or slips when walked on Ih-- LFT1Exercise Intensity HOW to Measure Your Heart RateConditioning Guidelines Aerobic ExerciseSuggested Stretches Part LISTmModel No Updght Base Blue Wire, 2 F Audio Wire Blue Wire, 2 FLarge Waming Decal Blue Wire, M/F Shock White Wire, 2 FemaleExploded DRAWING--Model No R1299A Full 90 DAY Warranty SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL