Gold's Gym GGEL66008.0 manual Maintenance and Troubleshooting, Console Troubleshooting

Page 22

MAINTENANCE AND TROUBLESHOOTING

Inspect and tighten all parts of the elliptical exerciser regularly. Replace any worn parts immediately.

To clean the elliptical exerciser, use a damp cloth and a small amount of mild soap. IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight.

CONSOLE TROUBLESHOOTING

If the console displays become dim, the batteries should be replaced; most console problems are the result of low batteries. See assembly step 10 on page 10 for replacement instructions. If the handgrip pulse sensor does not function properly, see step 5 on page 18.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the
reed switch should be adjusted. First, remove all of the
screws from both shields; there are three sizes of
screws in the shields—note which size of screw
you remove from each hole. Then, gently pry the
shields away from the frame.
Next, locate the
Reed Switch (50).	50		100 62
Turn the Pulley	50	78	100 62
Disc (62) until the		78
Magnet (100) is
aligned with the
Reed Switch.
Loosen, but do
not remove, the
indicated M4 x
16mm Screw
(78). Slide the
Reed Switch slightly closer to or away from the
Magnet, and then retighten the Screw. Rock the Pulley
Disc forward and backward just enough that the
Magnet passes the Reed Switch repeatedly. Adjust the
Screw until the console displays correct feedback.
When the Reed Switch is correctly adjusted, reattach
the shields. Note: If you have questions as to which
screw should be in which hole, see EXPLODED
DRAWING B on page 27 and the PART LIST on page
24.

HOW TO ADJUST THE BELT
If you can feel the pedals slip while you are pedaling,
even when the resistance of the pedals is at the high-
est setting, the Belt (74) may need to be adjusted.
First, remove all the screws from both shields; there
are three sizes of screws in the shields—note
which size of screw you remove from each hole.
Then, gently pry the shields away from the frame.
Next, turn the Belt
Adjustment Screw
(115) until the	74
Belt (74) is tight.
Then, reattach
the shields. Note:
If you have ques-
tions as to which
screw should be	115
in which hole, see
EXPLODED
DRAWING B on
page 27 and the PART LIST on page 24.

22

Image 22

Contents QUESTIONS? Model No. GGEL66008.0 Serial NoTable of Contents Important Precautions Before YOU Begin Assembly Wrench A rubber malletPage Page Avoid pinching Wire Harness Page Battery Avoid pinching Wires Grease 104Grease HOW to Fold and Unfold the Elliptical Exerciser HOW to USE the Elliptical ExerciserHOW to Move the Elliptical Exerciser HOW to Exercise on the Elliptical Exerciser HOW to Adjust the Stride of the Elliptical ExerciserConsole Diagram Features of the Console Select the manual mode HOW to USE the Manual ModeFollow your progress with the displays. The upper right Avoid moving your hands or gripping the con- tacts tightly Turn on the fan if desiredSelect a preset workout HOW to USE a Preset WorkoutBegin pedaling to start the workout Enter a target heart rate setting. a few seconds after you HOW to USE a Heart Rate WorkoutSelect a heart rate workout HOW to USE the Sound System HOW to USE AN Ifit WorkoutWhen you are finished exercising, remove the iFit card Insert an iFit card and select a workoutHOW to Adjust the Reed Switch Maintenance and TroubleshootingConsole Troubleshooting HOW to Adjust the BeltWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyKey No. Qty Description Key No. QtyQty Description Exploded Drawing A-Model No Exploded Drawing B-Model No. GGEL66008.0 R1008A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT