Star Trac S-UBX UPRIGHT BIKE manual Series Upright Bike Assembly and Setup, Unpacking

Page 12

ASSEMBLY AND SETUP

S SERIES UPRIGHT BIKE

ASSEMBLY AND SETUP

Use the following procedures to unpack and assemble your STAR TRAC S-UB /S-UBx UPRIGHT BIKE.

UNPACKING

Open the shipping carton, remove all parts from the carton and foam inserts, and verify that the following parts are included in your shipment:

Description

Qty

Bike Frame

1

Display Console Assembly

1

Seat Post Assembly

1

Front Foot

1

Rear Foot

1

Pedals (set of two)

1

Screw, Button Head, M10 X 30

8

Screw, Flat Head, M6 X 16

4

Screw, Socket Head, M6 X 10

1

TOOLS REQUIRED

Most STAR TRAC bikes can be assembled using the following tools:

n Metric Hex Key Wrenches

n

n

Metric Open-End Wrenches

n

n Metric Ratchet Socket Wrench Set

n

n

Torque Wrench

n

Channel Lock Pliers

Vice Grip Pliers

Rubber Mallet

Phillips Head Screwdriver

Your STAR TRAC S-UB /S-UBx UPRIGHT BIKE includes a hex key set and combination open-end wrench.

ASSEMBLY

1. Install the Front Foot

NOTE: The front foot assembly has wheels attached to the front edge. Be sure the wheels face forward when installing the front foot assembly.

Stand the bike frame upright and place the front foot assembly under the frame, aligning the holes in the foot with the holes in the frame.

NOTE: It may be necessary to raise the frame slightly to align the holes in the frame with the mating holes in the front foot.

Using four M10 X 30 button head screws, secure the front foot assembly to the frame. Tighten all four screws securely.

Step 1

12

STAR TRAC S SERIES BIKES OWNERS MANUAL

Image 12
Contents N E R ’ S M a N U a L Table of Contents Page Upright Bike Recumbent Bike Introduction About this ManualSafety Instructions PrecautionsDo Not Veiligheidsinstructies WaarschuwingConsignes DE Securite Mise EN GardeSicherheitsvorschriften WarnungInstruzioni DI Sicurezza AttenzioneInstruções DE Segurança AdvertênciaInstrucciones DE Seguridad AdvertenciaChinese Safety Instructions Here RådAdvarsler Japanese Safety Instructions Here Assembly and Setup Series Upright Bike Assembly and SetupAssembly UnpackingInstall the Rear Foot Install the Display ConsoleInstall the Seat Post Install the PedalsLeveling the Bike Series Recumbent Bike Assembly and Setup Install the Rear Foot Install the Seat Frame Seat Adjustments Adjusting Seat Height S-UB / S-UBx Upright BikeAdjusting Seat Position S-RB / S-RBx Recumbent Bike Operating InstructionsDisplay Panel Features Pedal Strap OperationUsing the Personal FAN Hints and Tips for Getting StartedCooldown Cycle To operate the bike during CooldownHeart Rate Monitoring Lockout ID ProcessingContact Heart Rate Monitoring Chest Strap Heart Rate MonitoringPreset Programs Quick StartManual Program To operate the Quick Start programBurn Calories Program To operate the Burn Calories programIncrease Endurance Program To operate the Increase Endurance programAdvanced Workouts Programs Heart Rate Control ProgramsTo operate the Constant Heart Rate Control program Program Heart Rate Training Range Upper LevelHeart Rate Training Range Lower Level Burn FAT Program Fitness TestTo operate the Burn FAT Control program Goal Workouts To operate the Fitness Test programTo operate the Calorie Goal program Auto Pilot Program To operate the Distance Goal programTo operate the Auto Pilot program Preventative Maintenance Daily MaintenanceWeekly Maintenance Manager / Maintenance Mode Monthly MaintenanceManager Mode Maintenance Mode LOE OFF Troubleshooting START-UP Service MessagesRegulatory Information Star Trac