WGT
Lxx
LOE LOI
1(lb)
1(kg)
N/A
OFF
001
500 | (lb) | 155 (lb) |
226 | (kg) | 70 (kg) |
N/A |
| LEN |
ON |
| OFF |
999 |
| 001 |
|
|
|
and cooldown.
Default Weight (to user). Typical weight in lb (UNx = UNE) or kg (UNx = UNM).
Language. Display language; either LEN (English), LGE (German), LSP (Spanish), LDU (Dutch), LPO (Portuguese), LFR (French), LIT (Italian), LSW (Swedish) or LKA (Katakana).
Lockout Enable. Enables/disables lockout function.
Lockout ID. Lockout override identification number.
MAINTENANCE MODE
Your Service Representative may need to check accumulated data about the past usage of your bike, test its display controls, or investigate error messages. For these reasons, your bike is equipped with a Maintenance Mode. The Maintenance Mode includes all of the items available through Manager Mode, plus additional items for Service and Diagnostic use. To enter Maintenance Mode:
1.Press and hold the 
, 
and 
keys together.
2.A beep will sound and “MAINTENANCE SETTINGS” will scroll once across the PROFILE Window.
3.Release all keys. “SN” will display in the PROFILE Window; the associated numeric value for the parameter will display in the DISTANCE Window.
NOTE: The system will automatically exit MAINTENANCE SETTINGS if no key is pressed for 30 seconds.
The following keys are used to modify MANAGER SETTINGS:
Increase and Decrease Level Keys: Display the next (Increase) and previous (Decrease) parameters. Keys will repeat if held.
Numeric Keypad: Facilitates entry of the desired value for the displayed parameter. These keys do not save the new value – see OK Key below.
OK Key: Updates (saves) the value of the displayed parameter in Flash memory. “UPDATING” will scroll once across the PROFILE Window while the update is in process. When the update is complete, the PROFILE Window will show the new value for the parameter.
NOTE: To exit maintenance SETTINGS without saving any values or settings, press the QUICK START key.
NOTE: Unless otherwise specified, the Item (parameter) name is shown in the PROFILE Window, and the value of the parameter is shown in the DISTANCE Window.
The items that you may display and change with the previous keys are:
Item | Lowest | Highest | Default | Meaning | |
Value | Value | Value | |||
|
|
|
|
|
|
SN | 0 |
| 9999 | N/A | Serial Number. S Series Bike serial number (set by factory). |
DSW | 1.0 | 99.99 | N/A | Display Software. Display panel software version number (set by factory). | |
|
|
|
|
| NOTE: Software checksum value is displayed in CALORIES Window. |
OHR | 0 |
| 9999 | 0 | Operating Hours. Total operating hours. |
DST | 0 |
| 9999 | 0 | Distance. Total distance ridden in miles or kilometers, based on current UNx |
|
|
|
|
| setting. |
UNx | UNE | UNM | UNE | Units. UNE (English) = units of pounds, miles, feet, inches | |
|
|
|
|
| UNM (Metric) = units of kilograms, kilometers, centimeters |
|
|
|
|
| NOTE: Current Value is shown in PROFILE Window. |
TIM | 5 |
| 99 | 99 | Time. Maximum time in minutes allowed for a program, excluding |
|
|
|
|
| and cooldown. |
WGT | 1 | (lb) | 500 (lb) | 155 (lb) | Default Weight (to user). Typical weight in lb (UNx = UNE) or kg (UNx = |
| 1 | (kg) | 226 (kg) | 70 (kg) | UNM). |
|
|
|
|
|
|
32 | STAR TRAC S SERIES BIKES OWNER’S MANUAL |