Precor C936i owner manual M M E R C I a L P R O D U C T S D I V I S I O N

Page 26

C O M M E R C I A L P R O D U C T S D I V I S I O N

VIEWING THE ODOMETER, HOURS OF USE, SOFTWARE VERSION, ERROR LOG AND SERIAL NUMBER

While the Precor banner is being displayed, press:

Stop, ENTER, QUICKSTART

Note:You need to press ENTER within ¹⁄₃ second after pressing the Stop button to initiate the Club Custom mode. (The RESET key may be used in place of the Stop button.)

The field name Odometer appears briefly and then the odometer value (the cumula- tive miles or kilometers users have travelled) appears. When either Select key is pressed the word “MILES” (or “KILOMETERS”) appears on the display to let you know the unit of measure.When the key is released, the odometer value reappears.

Press ENTER and the number of hours (Hour Meter) that the unit has been in use appears.The C936i notes the passing of minutes, but the numeric value that appears is truncated to the nearest full hour.When either SELECT key is pressed the word “HOURS appears on the display. When the key is released, the hour meter reappears.

Press ENTER and the unit’s three digit SW Version (upper display software version number) appears. Press either SELECT key to view the lower board’s software version number. The SELECT key toggles between the two versions. The words “UPPER” and “LOWER” appear prior to the version being displayed.

Press ENTER or the red STOP button and the Error Log appears. Press any ▼ or

▲key to scroll through the error codes. Up to ten error codes can be recorded and retrieved.

To view the odometer reading at the time the error was detected and the hours of use at the time the error occurred, press either SELECT key while the error code is being displayed. The SELECT keys act as toggles between the associated information.

Note: To clear (delete) the error log, press QUICKSTART for at least four seconds while viewing the list. Prompts appear on the display and let you know when the error messages have been deleted (“cleared” from memory).

Important:You cannot retrieve the error log once you have deleted it.

To view the serial number, press ENTER. Write the serial number onto the warranty registration form on page 50 and in the space provided on page 7. The serial number is helpful should you ever need to contact Customer Support.

To return to the Precor banner, press RESET, ENTER or the red STOP button.

page 26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents M M E R C I a L P R O D U C T S D I V I S I O N Important Safety Instructions Safety Approval Grounding InstructionsTable of Contents Maintenance Exercising on the TreadmillVoid the user’s authority to operate the equipment Radio Frequency Interference RFIEuropean Applications Obtaining Service About this ManualM M E R C I a L P R O D U C T S D I V I S I O N Other Equipment Unpacking the TreadmillStandard Equipment Hardware KIT Additional Tools NeededAssembly Instructions Setting Up the TreadmillInstallation Requirements Diagram Route cable Secure the display console to the upright supports. Diagram CsafeDiagram Attach handrails to the side and base brackets. Diagram Perform steps a. and b. on the opposite sideTest the heart rate feature. Diagram Install handrail First Tighten Level Unit Turning the Unit on and OFF Checking the Alignment of the Running Belt If the running belt ThenChanging the Club Settings Club InformationDisplay key functions within the Club Custom Mode Determining the Units of MeasureDetermining the Club Speed Limit Setting a Workout Time LimitSetting a Pause Time Limit To 18 kphM M E R C I a L P R O D U C T S D I V I S I O N Using Csafe Standard Equipment User ID Entry Program KeysFeatures on the Display Console C936i DisplaySetup Mode and Prompts Smartrate DisplayPress Quickstart at Setup Mode and the Quickstart FeatureWeight prompt Following occurs Precor bannerDisplay Features During a Workout M M E R C I a L P R O D U C T S D I V I S I O N Keys on the Display Console Keypad keysQuickstart DefaultValues Prompts Default ValueChanging the Display Features Using the Select KEY Using the Heart Rate Touch Capability Using the Security ClipUsing the Handrails Exercising on the TreadmillQuick Steps to Working OUT Keypad TipsWorkout Tips Continue your workout Cooling Down After a Workout Red Stop buttonPAUSE, Workout SUMMARY, and Exit Features StopPrograms Heart Rate FeatureUsing the Smartrate Feature Manual Mode and the Quickstart KEY 200 190 180 170 160 150 140 130 120 110 100To use the interval program, take the following steps Cross Country ProgramInterval Program Weight Loss Program Random ProgramHeart Rate Program Inspection MaintenanceCleaning the Equipment Perform a daily inspection of the treadmillAligning the Running Belt Long Term Storage Storing the Chest StrapServicing the Treadmill Thank You and Welcome to Precor Please indicate the type and number of products purchased Date of Purchase Purchased from Dealer nameProduct Serial Numbers How many members do you have?Conditions and Restrictions Limited WarrantyWarranty Periods and Coverage Complete this portion and keep for your recordsProduct Specifications Electronic Specifications
Top Page Image Contents