JVC RX-DP10VBK Adjusting the Parametric Equalizer —PARAMETRICEQ, Notes, 7Outputting the test tone

Page 47
7Adjusting the speaker channel output levels

7Adjustment procedure on this submenu7Outputting the test tone Adjusting the Speaker Channel Output Levels—LEVEL (1)

Notes:

• “TEST TONE” is not available if both speakers 1 and 2 are

LEVEL

 

 

 

 

TEST TONE

:OFF

FRONT L LEVEL:

0dB

CENTER LEVEL

:

0dB

FRONT R LEVEL:

0dB

SURR R LEVEL

:

0dB

SBACK R LEVEL:

0dB

SBACK L LEVEL:

0dB

SURR L LEVEL

:

0dB

SUBWOOFER

:

0dB

:OPERATE

 

:BACK

Notes:

On this submenu, you can adjust the speaker channel output levels. While outputting the test tone, select a speaker channel and adjust its output level.

Once adjustment is done on this submenu, it is stored for each source when you change the source or when you turn off the receiver.

deactivated or if Surround mode is turned off.

• If “NO” or “NONE” is selected for a speaker on the SPEAKER

SETTING submenu (page 36), test tone does not come out of

the speaker.

7Adjusting the speaker channel output levels

Select and adjust the following speakers:

FRONT L LEVEL

: Select this to adjust the left front

 

speaker output level within the range

 

of –20 dBto +10 dB, and – – – dB

 

(no sound).

 

 

FRONT R LEVEL

: Select this to adjust the right front

•The speaker level adjustments except the left/right front level and subwoofer level will be affected and be changed according to the Surround/DSP mode setting.

•You can show this submenu simply by pressing TEST button on the remote control. Test tone comes out of the activated speakers in sequence. (See page 49.)

7Adjustment procedure on this submenu

Adjustment is also possible without outputting the test tone. In this case, you can skip steps 1, 2 and 6 below.

1Press Þ or %(DOWN or UP) to select “TEST TONE.”

2Press # or @(RIGHT or LEFT) to output the test tone. (See “Outputting the test tone” below.)

3Press Þ or %(DOWN or UP) to select a speaker you want to adjust.

4Press # or @(RIGHT or LEFT) to adjust the speaker output level.

5Repeat step 3 and 4 to adjust the other speaker output levels.

6After adjustment is finished, stop the test tone.

1 Press % or Þ(UP or DOWN) to select “TEST TONE.” 2 Press # or @(RIGHT or LEFT) to select “OFF.”

7Outputting the test tone

CAUTION:

Test tone is automatically fixed to 0 dB, but this level will be louder than you would expect.

Select one of the following.

•Test tone will be heard about three seconds after you select “AUTO” or “MANUAL.”

AUTO : When this is selected, the test tone comes out of all the activated speakers in sequence (for 2 seconds each). The test tone comes out of the activated speakers in the following sequence:

Left front speaker = Center speaker = Right front speaker

=Right surround speaker = Right surround back speaker

=Left surround back speaker = Left surround speaker

=Subwoofer = (Back to the beginning)

MANUAL : When this is selected, the test tone comes out of only the speaker you select. (To select the speaker, see the right column.)

OFF

: Select this to stop the test tone.

 

speaker output level within the range of

 

–20 dBto +10 dB, and – – – dB(no

 

sound).

 

 

CENTER LEVEL

: Select this to adjust the center speaker

 

output level within the range of –10

 

dB to +10 dB.

 

 

SURR L LEVEL

: Select this to adjust the left surround

 

speaker output level within the range

 

of –10 dBto +10 dB.

 

 

SURR R LEVEL

: Select this to adjust the right surround

 

speaker output level within the range

 

of –10 dBto +10 dB.

 

 

SBACK L LEVEL

: Select this to adjust the left surround

 

back speaker output level within the

 

range of –10 dBto +10 dB.

 

 

SBACK R LEVEL

: Select this to adjust the right surround

 

back speaker output level within the

 

range of –10 dBto +10 dB.

 

 

SUBWOOFER

: Select this to adjust the subwoofer

 

output level within the range of –10

 

dB to +10 dB.

 

 

Note:

If “NO” or “NONE” is selected for a speaker on the SPEAKER

SETTING submenu (page 36), you cannot adjust its output level.

Adjusting the Parametric Equalizer —PARAMETRIC EQ (2)Manual background Adjusting the Parametric Equalizer —PARAMETRIC EQ (2)

 

 

 

 

On this submenu, you can

PARAMETRIC EQ

 

 

 

 

adjust equalization patterns

 

 

 

FRONT

 

according to your preference.

CENTER

SURROUND

First, select the signal channel

SURROUND BACK

 

 

 

 

(speaker) you want to adjust,

 

:ENTER

then move to its adjustment

 

:BACK

screen.

 

 

 

 

Notes:

•This function is applied only to the main room sources.

•If “NO” or “NONE” is selected for a speaker on the SPEAKER SETTING submenu (see page 36), you cannot select the corresponding channel.

•If THX Surround or DVD MULTI playback mode is in use, this submenu is not available.

Continued on the next page.

44

Page 46 Page 48
Image 47
Page 46 Page 48
Contents LVT0722-003A RX-DP10VBKAUDIO/VIDEO CONTROL RECEIVER INSTRUCTIONSWARNING: TO REDUCE THE RISK OF FIRE Caution ––STANDBY/ON switchCaution––SPEAKERLOAD SELECTOR switch Warnings, Cautions and OthersFor the main unit For the remote controlNote to CATV system installer Using the Surround Modes Table of ContentsBasic Settings Sound AdjustmentsRF/IR multi-brand/learningremote control FeaturesPrecautions IntroductionParts Identification 1SPEAKERS 1 button 18, Front PanelDisplay Window Refer to the pages in parentheses for details12 3 Getting Started Before InstallationConnecting the FM and AM Antennas Checking the Supplied AccessoriesMain room speaker layout Connecting the SpeakersAM Antenna Connections NotesBasic connecting procedure 3Insert the speaker signal cable2Turn the knob counterclockwise 4Turn the knob clockwisePower amplifier Power amplifierPower amplifier Power amplifier Connecting Audio/Video ComponentsR DVD L CD playerCD recorder Cassette deck or MD recorderVideo camera Video component connectionsVCRs Notes TV and/or DBS tunerDBS tuner DVD player Digital output terminal Digital ConnectionsDigital input terminals to the IR signal transmitter Setting Up the RF Rod AntennaSetting Up the IR Signal Transmitter 1. Find the place where you attach the IR signal3.Replace the cover Putting Batteries in the Remote ControlConnecting the Power Cord 2.Insert the batteriesSub-roomLayout Multi-RoomOperationsRequired Connections for Sub-Room Power amplifierLEARN/TRANSMIT selector to Basic Operating Procedure for Main Room1. Press STANDBY/ON 1. Set MAIN ROOM/SUB ROOM4. Press VOLUME +/– to adjust the Basic Operating Procedure for Sub-Room6. Turn MASTER VOLUME to adjust the volume level of theTo turn on the power, press Turning the Power On and Off StandbyMain Room Operations From the remote controlSpeaker and signal indicators on the display Canceling the Main Room OperationsSelecting the Main Room Source to Play SUBWFRas the VCR or DVD player, etc Adjusting the Main Room VolumeSUBWFR LFE 1. Press SOUND SELECTOR insideSelecting the Analog or Digital Input Mode Activating the Main Room Front SpeakersMuting the Main Room Sound Attenuating the Input Signalheadphones connected Press and hold INPUT MODE/INPUT INPUT MODETurning Line Direct On and Off Changing the Display BrightnessPress DIMMER Making Sounds NaturalFrom the remote control ONLY Using the Sleep TimerPress SLEEP repeatedly Basic adjustment auto memorythe SUB ROOM ON/OFF lamp lights Sub-RoomOperationsand Selecting the Sub-RoomOperations 2. Press SUB ROOM ON/OFF so thatFrom the remote control Canceling the Sub-RoomOperations“SUB ROOM.” From the remote controlOn the unit Adjusting the Sub-RoomVolumeSelecting the Sub-RoomSource to Play From the remote controlMuting the Sub-RoomSound Activating the Sub-RoomFront SpeakersPress SPEAKERS 2/SUB ROOM to activate the sub-roomfront speakers1. Press FM or AM Tuning into Stations Manually2.Press TUNING UP or TUNING Receiving Radio Broadcaststhe front door to select a Using Preset Tuning2. Press SET inside the front door 3. Press RIGHT or LEFT insideSetup Menu Configuration Basic SettingsFor the main room operations Operation through On-ScreenDisplay MenusFrom the remote control Menu operation buttonsrepeatedly to select an item Menu Operating Procedure1. Press SETUP MENU 3. Press SET7For subwoofer Setting the Speakers —SPEAKERSETTINGSetting the Speaker Distance —SPEAKERDISTANCE LSB RSB7Changing the sound phase Setting the Bass Sounds—SUBWOOFER37Setting the crossover frequency 7Setting the low frequency effect attenuator LFE7Setting THX Surround EX Setting the Dynamic Range —DYNAMICRANGESetting the Digital Input Terminals -DIGITALIN 7Setting the Midnight modeWhen “COAXIAL INPUT” is set to “TV” or “DBS” Turning On and Off the Video Output —VIDEOPOWERWhen “COAXIAL INPUT” is set to “DVD” When “COAXIAL INPUT” is set to “CD”Preparing for the Sub-RoomOperations —SUBROOM p Adjustment Menu Configuration Sound AdjustmentsFor the main room operations From the remote controlOperation through On-ScreenDisplay Menus Menu operation buttonsrepeatedly to select an item 1. Press ADJUST MENUMenu Operating Procedure 3. Press SETNotes Adjusting the Parametric Equalizer —PARAMETRICEQ7Adjusting the speaker channel output levels 7Adjustment procedure on this submenu7Adjustment screen Adjusting the DSP Parameters —DSPPARAMETERAdjusting the Center Channel —CENTERCHANNEL 7 Adjustment procedure on this submenuTHX Surround EX Dolby Digital EX Using the Surround ModesReproducing Theater Ambience Introducing the Surround ModesDTS Digital Surround Surround modes available for input signalsInput Signals Dolby Surround Dolby Pro Logic1.Select and play any sound source Activating the Surround Modesoutput balance Adjusting the Surround Sounds Temporarily1. Press SOUND 2. Press TEST once to check the speakerDAP modes Using the DSP ModesReproducing the Sound Field Introducing the DSP Modes1.Select and play any sound source Activating the DSP Modes2.Press DSP MODE repeatedly until the DSP mode you want appears on the display4. Press LIVENESS to adjust the Adjusting the DSP Parameters Temporarily2. Press EFFECT to adjust the overall 3. Press ROOM SIZE to adjust the roomActivating the DVD MULTI Playback Mode Using the DVD MULTI Playback ModeFor the main room operations COMPU LINK Remote Control SystemNotes Automatic Source Selection3. Press the play 3 button on the CD player the same timeFUNCTIONS TEXT COMPU LINK Remote Control SystemCONNECTIONS Note on OPERATIONSDisc Information screen To exit from the Disc information screen4. Press %/ Þ/ @/ #to 2. Press %/ Þto move to “SEARCH,” then press SET3. Press %/ Þto move to “PERFORMER,” then press SET2. Press %/ Þto move to “SEARCH,” then press SET 3.Press %/ Þto move to “GENRE,” then press SET2. Press %/ Þto move to “TITLE INPUT,” then press SET7. Press %/ Þ/ @/ #to move to “DISC 32 characters5.Press %/ Þ/ @/ #to move to “DISC MICHAEL in this example,” then press SETCONNECTIONS 2: AV COMPU LINK Connection AV COMPU LINK Remote Control SystemCONNECTIONS 1: IR Signal Transmitter Connection One-TouchVideo Play CONNECTIONS 3: Video Cable ConnectionNotes Automatic Power On/Off StandbyAutomatic Power On One-TouchDVD PlaySound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder CD playerCD player-changer TurntableDVD player Operating Video ComponentsVCR VCR connected to the VCR 1 jacks 2.Press and hold TV/CATV/DBS STANDBY/ON Changing the Preset Signal CodesOperating Other Manufacturers’ Equipment 1.Set the TV operation mode selector to “TV.”buttons 1–9,and 3.Enter manufacturer’s code using buttons 1-9,and4. Enter manufacturer’s code using 1.Press and hold VCR STANDBY/ON 2.Press VCR1. Press and hold AUDIO ON. STANDBY ON 3. Enter manufacturer’s code using1.Press and hold VCR STANDBY/ON 2.Press DVD 4. Release AUDIO ONManufactures’ codes for DBS tuner selector to “LEARN.” Storing the Remote Signals Manually1. Set the LEARN/TRANSMIT MAIN ROOM/SUB ROOMNotes •Repeat steps 3 to 5 to store more signals in acontrol different remote mode source1. Set the LEARN/TRANSMIT 3. Press the desired buttonTo use the stored signals To erase the stored signalsPOSSIBLE CAUSE TroubleshootingPROBLEM SOLUTIONContinuous hissing or buzzing during FM reception Amplifier Specifications120 W per channel, min. RMS, driven into 8 Ω, General Tuning RangeFM tuner IHF AM tunerDo not service the television yourself AccessoriesAuthorized Service Centers HOW TO LOCATE YOUR JVC SERVICE CENTERAUDIO-2 LIMITED WARRANTYWHAT YOU MUST DO FOR WARRANTY SERVICE WHAT IS NOT COVEREDVICTOR COMPANY OF JAPAN, LIMITED 0701NHMMDWJEIN
Top Page Image Contents