JVC RX-DP10VBK manual AV COMPU LINK Remote Control System, CONNECTIONS 2: AV COMPU LINK Connection

Page 64
AV COMPU LINK Remote Control System

CONNECTIONS 1: IR Signal Transmitter ConnectionCONNECTIONS 2: AV COMPU LINK Connection AV COMPU LINK Remote Control System

This receiver is equipped with the AV COMPU LINK-III. The AV COMPU LINK remote control system allows you to operate JVC video components (TV, VCR, and DVD player) through the receiver. To use this remote control system, you need to connect the video components you want to operate, following the procedure below.

•Refer also to the manual supplied with your video components.

1.If you have already plugged your VCR 1 (VCR connected to the VCR 1 jacks), DVD player, TV, and this receiver into the AC outlets, unplug their AC power cords first.

2.Connect the IR signal transmitter (supplied) to the IR OUT on the rear, and place it so that it is aimed at the remote sensor on the target video component(s).

•See “CONNECTIONS 1” below (and page 15 for details).

3.Connect your VCR 1, DVD player, TV, and this receiver as follows, using the cables with the monaural mini-plugs (not supplied).

•See “CONNECTIONS 2” below.

4.Connect the audio input/output jacks on VCR 1, DVD player, TV, and this receiver using the cables with RCA pin plug.

•See pages 11 to 13.

5.Connect the video input/output jacks on VCR 1, DVD player, TV, and this receiver, using the cables with RCA pin plugs, with S-video plugs or with component video plugs.

•See “CONNECTIONS 3” on the next page (and pages 11 to 13 for details).

6.Plug the AC power cords of the components into the AC outlets.

7.When turning on the TV for the first time after the AV COMPU LINK connection, turn the TV volume to the minimum using the TV volume control on the TV.

8.Turn on the other connected components first, then turn on this receiver.

• When turning on the VCR 1, use the remote control supplied with this receiver—press VCR 1

 

(STANDBY/ON).

CONNECTIONS 1: IR Signal Transmitter Connection

RF REMOTE ANTENNA

Target video component(s)

On the rear panel

BAND1

 

BAND2

IR OUT

 

At an angle of

approx. 60°

IR signal transmitter

CONNECTIONS 2: AV COMPU LINK Connection

VCR 1

DVD player

VHS

DVD

AV

COMPU LINK

AV

COMPU LINK

RX-DP10VBK

Notes:

TV

AV COMPU LINK EX

AV

COMPU LINK III

CAUTION:

When connecting the TV with the AV COMPU LINK remote control system, connect the receive to the AV COMPU LINK EX or AV COMPU LINK III terminal.

DO NOT connect the receiver to the AV COMPU LINK RECEIVER/ AMP terminal.

•The AV COMPU LINK remote control system cannot control the DBS tuner connected to the TV SOUND/DBS jacks, and video components connected to the VIDEO and VCR 2 jacks on the receiver.

•When connecting only the VCR 1 or DVD player to this receiver, connect it directly to the receiver using a cable with the monaural mini- plugs.

•When connecting the receiver and the TV with AV COMPU LINK EX terminal by using the component video cables, you cannot use Automatic Selection of TV’s Input Mode (see page 63).

61

Page 63 Page 65
Image 64
Page 63 Page 65
Contents RX-DP10VBK AUDIO/VIDEO CONTROL RECEIVERINSTRUCTIONS LVT0722-003ACaution ––STANDBY/ON switch Caution––SPEAKERLOAD SELECTOR switchWarnings, Cautions and Others WARNING: TO REDUCE THE RISK OF FIRENote to CATV system installer For the remote controlFor the main unit Table of Contents Basic SettingsSound Adjustments Using the Surround ModesFeatures PrecautionsIntroduction RF/IR multi-brand/learningremote controlParts Identification Front Panel Display WindowRefer to the pages in parentheses for details 1SPEAKERS 1 button 18,12 3 Before Installation Connecting the FM and AM AntennasChecking the Supplied Accessories Getting StartedConnecting the Speakers AM Antenna ConnectionsNotes Main room speaker layout3Insert the speaker signal cable 2Turn the knob counterclockwise4Turn the knob clockwise Basic connecting procedurePower amplifier Power amplifier Power amplifierConnecting Audio/Video Components Power amplifierCD player CD recorderCassette deck or MD recorder R DVD LVCRs Video component connectionsVideo camera DBS tuner TV and/or DBS tunerNotes DVD player Digital input terminals Digital ConnectionsDigital output terminal Setting Up the RF Rod Antenna Setting Up the IR Signal Transmitter1. Find the place where you attach the IR signal to the IR signal transmitterPutting Batteries in the Remote Control Connecting the Power Cord2.Insert the batteries 3.Replace the coverMulti-RoomOperations Required Connections for Sub-RoomPower amplifier Sub-roomLayoutBasic Operating Procedure for Main Room 1. Press STANDBY/ON1. Set MAIN ROOM/SUB ROOM LEARN/TRANSMIT selector toBasic Operating Procedure for Sub-Room 6. Turn MASTER VOLUME toadjust the volume level of the 4. Press VOLUME +/– to adjust theTurning the Power On and Off Standby Main Room OperationsFrom the remote control To turn on the power, pressCanceling the Main Room Operations Selecting the Main Room Source to PlaySUBWFR Speaker and signal indicators on the displayAdjusting the Main Room Volume SUBWFR LFE1. Press SOUND SELECTOR inside as the VCR or DVD player, etcActivating the Main Room Front Speakers Selecting the Analog or Digital Input ModeAttenuating the Input Signal headphones connectedPress and hold INPUT MODE/INPUT INPUT MODE Muting the Main Room SoundChanging the Display Brightness Press DIMMERMaking Sounds Natural Turning Line Direct On and OffUsing the Sleep Timer Press SLEEP repeatedlyBasic adjustment auto memory From the remote control ONLYSub-RoomOperations and Selecting the Sub-RoomOperations2. Press SUB ROOM ON/OFF so that the SUB ROOM ON/OFF lamp lightsCanceling the Sub-RoomOperations “SUB ROOM.”From the remote control From the remote controlAdjusting the Sub-RoomVolume Selecting the Sub-RoomSource to PlayFrom the remote control On the unitActivating the Sub-RoomFront Speakers Press SPEAKERS 2/SUB ROOM toactivate the sub-roomfront speakers Muting the Sub-RoomSoundTuning into Stations Manually 2.Press TUNING UP or TUNINGReceiving Radio Broadcasts 1. Press FM or AMUsing Preset Tuning 2. Press SET inside the front door3. Press RIGHT or LEFT inside the front door to select aBasic Settings Setup Menu ConfigurationOperation through On-ScreenDisplay Menus From the remote controlMenu operation buttons For the main room operationsMenu Operating Procedure 1. Press SETUP MENU3. Press SET repeatedly to select an itemSetting the Speakers —SPEAKERSETTING Setting the Speaker Distance —SPEAKERDISTANCELSB RSB 7For subwooferSetting the Bass Sounds—SUBWOOFER3 7Setting the crossover frequency7Setting the low frequency effect attenuator LFE 7Changing the sound phaseSetting the Dynamic Range —DYNAMICRANGE Setting the Digital Input Terminals -DIGITALIN7Setting the Midnight mode 7Setting THX Surround EXTurning On and Off the Video Output —VIDEOPOWER When “COAXIAL INPUT” is set to “DVD”When “COAXIAL INPUT” is set to “CD” When “COAXIAL INPUT” is set to “TV” or “DBS”Preparing for the Sub-RoomOperations —SUBROOM p Sound Adjustments Adjustment Menu ConfigurationFrom the remote control Operation through On-ScreenDisplay MenusMenu operation buttons For the main room operations1. Press ADJUST MENU Menu Operating Procedure3. Press SET repeatedly to select an itemAdjusting the Parametric Equalizer —PARAMETRICEQ 7Adjusting the speaker channel output levels7Adjustment procedure on this submenu NotesAdjusting the DSP Parameters —DSPPARAMETER Adjusting the Center Channel —CENTERCHANNEL7 Adjustment procedure on this submenu 7Adjustment screenUsing the Surround Modes Reproducing Theater AmbienceIntroducing the Surround Modes THX Surround EX Dolby Digital EXSurround modes available for input signals Input SignalsDolby Surround Dolby Pro Logic DTS Digital SurroundActivating the Surround Modes 1.Select and play any sound sourceAdjusting the Surround Sounds Temporarily 1. Press SOUND2. Press TEST once to check the speaker output balanceUsing the DSP Modes Reproducing the Sound FieldIntroducing the DSP Modes DAP modesActivating the DSP Modes 2.Press DSP MODE repeatedly until the DSP modeyou want appears on the display 1.Select and play any sound sourceAdjusting the DSP Parameters Temporarily 2. Press EFFECT to adjust the overall3. Press ROOM SIZE to adjust the room 4. Press LIVENESS to adjust theUsing the DVD MULTI Playback Mode Activating the DVD MULTI Playback ModeCOMPU LINK Remote Control System NotesAutomatic Source Selection For the main room operationsthe same time 3. Press the play 3 button on the CD playerCONNECTIONS TEXT COMPU LINK Remote Control SystemFUNCTIONS OPERATIONS Disc Information screenTo exit from the Disc information screen Note on2. Press %/ Þto move to “SEARCH,” then press SET 3. Press %/ Þto move to “PERFORMER,”then press SET 4. Press %/ Þ/ @/ #to3.Press %/ Þto move to “GENRE,” then press SET 2. Press %/ Þto moveto “TITLE INPUT,” then press SET 2. Press %/ Þto move to “SEARCH,” then press SET32 characters 5.Press %/ Þ/ @/ #to move to “DISCMICHAEL in this example,” then press SET 7. Press %/ Þ/ @/ #to move to “DISCCONNECTIONS 1: IR Signal Transmitter Connection AV COMPU LINK Remote Control SystemCONNECTIONS 2: AV COMPU LINK Connection CONNECTIONS 3: Video Cable Connection One-TouchVideo PlayAutomatic Power On/Off Standby Automatic Power OnOne-TouchDVD Play NotesOperating JVC’s Audio/Video Components Operating Audio ComponentsTuner Sound control section AmplifierCD player CD player-changerTurntable CD recorderVCR VCR connected to the VCR 1 jacks Operating Video ComponentsDVD player Changing the Preset Signal Codes Operating Other Manufacturers’ Equipment1.Set the TV operation mode selector to “TV.” 2.Press and hold TV/CATV/DBS STANDBY/ON3.Enter manufacturer’s code using buttons 1-9,and 4. Enter manufacturer’s code using1.Press and hold VCR STANDBY/ON 2.Press VCR buttons 1–9,and3. Enter manufacturer’s code using 1.Press and hold VCR STANDBY/ON 2.Press DVD4. Release AUDIO ON 1. Press and hold AUDIO ON. STANDBY ONManufactures’ codes for DBS tuner Storing the Remote Signals Manually 1. Set the LEARN/TRANSMITMAIN ROOM/SUB ROOM selector to “LEARN.”•Repeat steps 3 to 5 to store more signals in a controldifferent remote mode source Notes3. Press the desired button To use the stored signalsTo erase the stored signals 1. Set the LEARN/TRANSMITTroubleshooting PROBLEMSOLUTION POSSIBLE CAUSEContinuous hissing or buzzing during FM reception 120 W per channel, min. RMS, driven into 8 Ω, SpecificationsAmplifier Tuning Range FM tuner IHFAM tuner GeneralAccessories Authorized Service CentersHOW TO LOCATE YOUR JVC SERVICE CENTER Do not service the television yourselfLIMITED WARRANTY WHAT YOU MUST DO FOR WARRANTY SERVICEWHAT IS NOT COVERED AUDIO-20701NHMMDWJEIN VICTOR COMPANY OF JAPAN, LIMITED
Top Page Image Contents