JVC RX-DP10VBK manual Adjusting the DSP Parameters Temporarily, Press EFFECT to adjust the overall

*When multichannel signals come in, you cannot select “STEREO FILM” and “MONO FILM.”

Notes:

•	When the surround speakers are deactivated, the 3D-PHONIC
	processing is applied to the DSP modes (the 3D-PHONIC indicator
	also lights up).
•	If “USER MODE 1” (then “NO DATA”) appears, press and hold DSP

Before you start, remember...

•Adjustments using the number buttons are temporary and cannot be stored.

When you change the source or turn off the power, the adjustments are erased.

•When you select “ALL CH STEREO,” you cannot adjust the DSP parameters.

MODE on the unit until it disappears. (This mode is only for service

personnel.)

1. Press SOUND.

SOUND

To cancel the DSP modes

Press DSP MODE repeatedly until “SURROUND OFF” appears on the display.

•When a pair of headphones is connected or when the front speakers are deactivated, “HEADPHONE” will appear.

If you want to modify the stored sound adjustments temporarily

See “Adjusting Surround Sounds Temporarily” on page 49.

•When adjusting the surround sounds for the DSP modes, you cannot output the test tone.

•When you select “3D THEATER,” you cannot adjust the surround speaker levels and surround back speaker levels.

Adjusting the DSP Parameters Temporarily

Activating the DSP mode for a source automatically recalls the memorized DSP parameter settings done on the Adjustment Menu.

However, if you want to modify the stored adjustments temporarily only for the current playback source, you can use the number buttons on the remote control.

IMPORTANT:

Check to see if the following before or while using the buttons and controls.

For the main room operations:

The MAIN ROOM ON/OFF lamp on the unit is lit.

•When using the remote control:

–Set the MAIN ROOM/SUB ROOM (LEARN/TRANSMIT) selector to “MAIN ROOM.”

–Check the indication shown on the remote’s display when you press a button—this indicates the remote control operation mode together with multi-room operation mode (either MAIN ROOM or SUB ROOM) for a while (10 or 5 seconds).

	LEARN TRANSMIT
		STANDBY	ON
	MAIN ROOM SUB ROOM
LEARN TRANSMIT	MAIN ROOM	SUB ROOM TV/CATV/DBS	VCR 1
	ON/OFF	ON/OFF
		STANDBY/ON	STANDBY/ON

The 10 keys are activated for sound adjustments.

2. Press EFFECT to adjust the overall	EFFECT
level of the effect.	3

•Each time you press the button, the effect level changes as follows:

EFFECT 1 EFFECT 2 EFFECT 3

EFFECT 5 EFFECT 4

As the number increases, the selected DSP effect becomes stronger. (Normally set it to “EFFECT 3.”)

3. Press ROOM SIZE to adjust the room	ROOM SIZE
size (sense of spaciousness).	6

•Each time you press the button, the display changes to show the following:

ROOM SIZE 1 ROOM SIZE 2 ROOM SIZE 3

ROOM SIZE 5 ROOM SIZE 4

As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room. (Normally set it to “ROOM SIZE 3.”)

4. Press LIVENESS to adjust the	LIVENESS
liveness.	9

•Each time you press the button, the display changes to show the following:

LIVENESS 1 LIVENESS 2 LIVENESS 3

LIVENESS 5 LIVENESS 4

As the number increases, the attenuation level of reflections over time decreases so that acoustics change from “Dead” to “Live.” (Normally set it to “LIVENESS 3.”)

5. Press WALL to adjust the wall type.				WALL
				+10
• Each time you press the button, the display
				100+
changes to show the following:
WALL TYPE 1	WALL TYPE 2		WALL TYPE 3
WALL TYPE 5		WALL TYPE 4

MAIN ROOM SUB ROOM

MAIN ROOM

Ex. When you press SOUND with

MAIN ROOM/SUB ROOM (LEARN/TRANSMIT) selector set to “MAIN ROOM.”

As the number increases, the hardness of the wall to be simulated changes from “Soft” to “Hard.” (Normally set it to “WALL TYPE 3.”)

Notes:

•You cannot adjust “SEAT POSITION” using the number buttons. If you want to adjust it, see page 45.

•When the front speakers are deactivated, you cannot adjust the DSP parameters.

52