Operating Other Manufacturers’ Equipment, Notes

CATV/

DBS

Operating Other Manufacturers’ Equipment

You can use this remote control supplied for this unit for operating the other manufacturers’ components, either by changing the preset signal codes or by using the learning function (see page 71).

IMPORTANT:

•To operate the other component(s) using the RF signals emitted from this remote control, the IR signal transmitter and the RF rod antenna must be connected to this receiver.

–Place the IR signal transmitter so that it is aimed at the remote sensor(s) on the target component(s).

–The RF signal-reachable distance may differ depending on the operating conditions and circumstances.

–The IR signal transmitter can send signals at a distance of 10 feet (3 m).

When using the remote control:

Changing the Preset Signal Codes

By changing the transmittable signals from preset ones to the other manufacturers’, you can operate the other manufacturer’s components using this remote control.

•When operating the other manufacturers’ components, refer also to the manuals supplied with them.

To change the transmittable signals for operating another manufacturer’s TV

–Set the MAIN ROOM/SUB ROOM (LEARN/TRANSMIT) selector to “MAIN ROOM” or “SUB ROOM” correctly.

LEARN TRANSMIT

MAIN

MAIN ROOM SUB ROOM

ROOM

SUB

ROOM

– Set the TV operation mode selector to “TV” or “CATV/DBS” correctly.

To operate TV, set it to “TV.”

To operate the CATV converter or the DBS tuner, set it to “CATV/DBS.”

–Check the indication shown on the remote’s display

when you press a button—this indicates the remote control operation mode together with multi-room operation mode (either MAIN ROOM or SUB ROOM) for a while (10 or 5 seconds).

LEARN TRANSMIT		LEARN TRANSMIT
STANDBY	ON	STANDBY	ON
MAIN ROOM SUB ROOM		MAIN ROOM SUB ROOM

1.Set the TV operation mode selector to “TV.”

2.Press and hold TV/CATV/DBS

(STANDBY/ON).

3. Press TV/DBS.

Remote’s display

4. Enter manufacturer’s code using buttons 1–9, and 0.

See page 69 to find the code.

CATV/

DBS

TV/CATV/DBS

STANDBY/ON

TV/DBS

EFFECT

1 2 3

		ROOM SIZE
4	5	6

LIVENESS

7/P 8 9

WALL

MAIN ROOM	SUB ROOM TV/CATV/DBS	VCR 1	MAIN ROOM	SUB ROOM TV/CATV/DBS	VCR 1
ON/OFF	ON/OFF		ON/OFF	ON/OFF
	STANDBY/ON	STANDBY/ON		STANDBY/ON	STANDBY/ON

10	0	+10
RETURN	FM MODE	100+

MAIN ROOM

SUB ROOM

Ex. When you press VCR1	Ex. When you press VCR1
with MAIN ROOM/SUB	with MAIN ROOM/SUB
ROOM (LEARN/	ROOM (LEARN/
TRANSMIT) selector	TRANSMIT) selector
set to “MAIN ROOM.”	set to “SUB ROOM.”

CAUTION:

When replacing the batteries, finish it without delay; otherwise, manufactures’ codes are lost.

5. Release TV/CATV/DBS (STANDBY/ON).

After setting the TV operation mode selector to “TV,” you can perform the following operations on the TV:

TV/CATV/DBS			(STANDBY/ON):
		Turns on or off the TV.
TV VOL +/–	: Adjusts the volume.
TV/VIDEO	: Sets the input mode (either TV or VIDEO).

After pressing TV/DBS (with the TV operation mode selector set to “TV”), you can perform the following operations on a TV:

CHANNEL +/–		: Changes the channels.
1 – 10, 0, 100+ (+10)		: Selects the channels.
		Number button 10 will function as
		the ENTER button if your TV
		requires pressing ENTER after
		selecting a channel number.
Notes:

•Refer to the manual supplied for your TV.

•All the functions listed above may not be assigned to the buttons for some TVs.

•If you cannot change the channels of some TVs by pressing number buttons, press CHANNEL +/– for changing the channels.

6. Try to operate your TV by pressing

TV/CATV/DBS (STANDBY/ON).

When your TV turns on or off, you have entered the correct code.

TV/CATV/DBS

STANDBY/ON

If there are more than one code listed for your brand of TV,

try each one until the correct one is entered.