ProForm PFSY59001 user manual Cable Trap is oriented to hold the Cable in place

Page 18

46.Remove the 3/8” Nylon Locknut (50) from the indi- cated 3/8” x 5 1/2” Bolt (55).

Wrap the Leg Press Cable (75) around a 3 1/2” Pulley (24). Secure the Pulley and a Cable Trap (25) to the 3/8” x 5 1/2” Bolt (55) on the indicated side of the Press Base (6) with the 3/8” Nylon Locknut (50). Be sure the Cable Trap is oriented to hold the Cable in place.

Press a 2 1/2” Square Inner Cap (76) into the Press Base (6).

47.Remove the 3/8” Nylon Locknut (50) from the indi- cated 3/8” x 6” Bolt (59).

Wrap the Leg Press Cable (75) around a 3 1/2” Pulley (24) in the direction shown. Secure the Pulley and a Cable Trap (25) to the 3/8” x 6” Bolt

(59)on the indicated side of the Press Leg Lever

(90)with the 3/8” Nylon Locknut (50).Be sure the

Cable Trap is oriented to hold the Cable in place.

48.Remove the indicated 3/8” Nylon Locknuts (50).

Wrap the Leg Press Cable (75) around a 3 1/2” Pulley (24). Attach the Pulley and a Cable Trap (25) to the 3/8” x 4 3/4” Bolt (60), on the indicated side of the Press Seat Frame (7), with the first 3/8” Nylon Locknut (50).

Wrap the Leg Press Cable (75) around a 3 1/2” Pulley (24). Attach the Pulley and a Cable Trap (25) to the 3/8” x 4 3/4” Bolt (60), on the indicated side of the Press Frame (8), with a 3/8” Nylon Locknut (50).

Be sure the Cable Traps (25) are oriented to hold the Cable (75) in place.

49.Remove the indicated 3/8” Nylon Locknut (50).

Attach the Leg Press Cable (75) to the 3/8” x 3 3/4” Bolt (102) on the indicated side of the Press Upright

(2)with the 3/8” Nylon Locknut (50).

18

46

 

 

 

76

 

 

 

24

 

55

 

6

25

 

 

50

 

75

47

 

 

59

 

 

90

 

75

 

 

 

25

50

 

24

 

 

48

7

 

 

 

 

60

25

 

 

24

 

25

50

 

 

 

24

75

 

8

 

49

 

 

 

2

 

 

 

102

 

 

50

 

 

75

Image 18
Contents QUESTIONS? Model No. PFSY59001 Serial NoCustomer HOT Line Table of Contents Important Precautions Before YOU Begin DecalAssembly Make Assembly EasierFrame Assembly Do not tighten the Nylon Locknuts 50 yet Do not tighten the Nylon Locknuts yet Locate and open the parts bag labeled ARM Assembly Tighten the Nylon Locknuts 50 used in stepsPage Cable Assembly Page Page Weight Cable is in the groove of the Pulley Page Page Page Cable Trap is oriented to hold the Cable in place Seat Assembly Locate and open the parts bag labeled Seat AssemblyPage Adjustments Changing the Weight SettingAttaching the LAT BAR or AB Strap to High Pulley Station Adjusting the Backrest Adjusting the Curl PADAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesButterfly Cable Cable DiagramsLeg Press Cable Press Upright Ab Cable Left ArmWeight Cable Cable ID Stack Low Pulley Part Identification CHART-Model No. PFSY59001 R0402AX 4 Bolt X 5 1/2 Bolt X 6 Bolt 2 x 2 1/2 Inner Cap 2 Square Inner Cap Round Inner Cap Part LIST-Model No. PFSY59001 Key No. Qty DescriptionExploded Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT