ProForm PFSY59001 user manual Frame Assembly

Page 6

FRAME ASSEMBLY

1.Before you begin this step, make sure that you have read all of the information on page 5. This brief introduction will save you much more time than it takes to read it.

Locate and open the parts bags labeled “FRAME ASSEMBLY.”

See the inset drawing. Insert two 1 1/2” x 2 1/2” Inner Caps (83) and two 3/8” x 2” Carriage Bolts (92) into the Butterfly Base (4).

Insert two 1 1/2” x 2 1/2” Inner Caps (83) into the indicated ends of the Butterfly Base (4) and the Press Base (6). Insert six 3/8” x 2” Carriage Bolts (92) into the Butterfly Base and the Press Base.

Attach the Butterfly Base (4) to the Press Base (6) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Washers (48), and two 3/8” Nylon Locknuts (50).

2.Attach the Butterfly Upright (1) to the indicated 3/8” x 2” Carriage Bolts (92) in the Butterfly Base (4) with two 3/8” Nylon Locknuts (50).Do not tighten the Nylon Locknuts yet. Be sure the Upright is attached in the position shown.

Attach the Press Upright (2) to the indicated 3/8” x 2” Carriage Bolts (92) in the Press Base (6) with two 3/8” Nylon Locknuts (50).Do not tighten the

Nylon Locknuts yet. Be sure the Upright is attached in the position shown.

3.Make sure the Plastic Bushing (52) is in the top of the Butterfly Front Leg (3).

Attach the Butterfly Front Leg (3) to the indicated 3/8” x 2” Carriage Bolts (92) in the Butterfly Base

(4) with two 3/8” Nylon Locknuts (50).Do not tight- en the Nylon Locknuts yet. Make sure that the Butterfly Front Leg is turned so that the welded “U”-bracket is on the side shown.

6

1

 

 

83

48

62

 

 

 

 

 

50

 

 

48

 

 

 

 

 

 

 

 

 

 

4

6

 

 

 

 

 

 

 

 

 

92

 

 

 

92

 

 

83

 

 

 

 

 

83

92

 

 

 

 

 

 

 

 

 

 

 

 

92

83

4

 

 

 

 

2

 

 

 

 

 

 

 

2

 

 

1

 

 

 

 

 

 

 

50

50

 

 

50

 

 

 

50

 

 

 

 

6

 

 

 

 

4

 

92

 

92

 

3

 

52

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

“U”-bracket

 

 

50

 

 

 

 

 

 

50

 

 

 

4

92

 

 

 

 

 

 

 

 

Image 6
Contents QUESTIONS? Model No. PFSY59001 Serial NoCustomer HOT Line Table of Contents Important Precautions Before YOU Begin DecalAssembly Make Assembly EasierFrame Assembly Do not tighten the Nylon Locknuts 50 yet Do not tighten the Nylon Locknuts yet Locate and open the parts bag labeled ARM Assembly Tighten the Nylon Locknuts 50 used in stepsPage Cable Assembly Page Page Weight Cable is in the groove of the Pulley Page Page Page Cable Trap is oriented to hold the Cable in place Seat Assembly Locate and open the parts bag labeled Seat AssemblyPage Adjustments Changing the Weight SettingAttaching the LAT BAR or AB Strap to High Pulley Station Adjusting the Backrest Adjusting the Curl PADAttaching the AB Strap to the AB Pulley Station Weight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesButterfly Cable Cable DiagramsLeg Press Cable Press Upright Ab Cable Left ArmWeight Cable Cable ID Stack Low Pulley Part Identification CHART-Model No. PFSY59001 R0402AX 4 Bolt X 5 1/2 Bolt X 6 Bolt 2 x 2 1/2 Inner Cap 2 Square Inner Cap Round Inner Cap Part LIST-Model No. PFSY59001 Key No. Qty DescriptionExploded Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT