ProForm PFSY59001 user manual Adjustments, Changing the Weight Setting

Page 21

ADJUSTMENTS

The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPORTANT:

When attaching the lat bar, ab strap, or nylon strap, make sure that the attachments are in the correct starting position for the exercise to be performed. If there is any slack in the cables or chain as an exer- cise is performed, the effectiveness of the exercise will be reduced.

CHANGING THE WEIGHT SETTING

 

 

To change the weight setting of the weight stack,

 

 

insert the Weight Pin (19) under the desired Weight

 

 

(21) until the bent end of the Weight Pin is touching

 

 

the Weights. Turn the bent end downward. The

 

 

weight setting can be changed from 10 pounds to 200

 

 

pounds, in 10 pound increments. Note: Due to the

 

 

cables and pulleys, the amount of resistance at

 

 

each exercise station may vary from the weight

 

 

setting. Use the WEIGHT RESISTANCE CHART on

 

 

page 23 to find the approximate amount of resis-

 

 

tance at each weight station.

 

 

 

21

 

 

19

 

ATTACHING THE LAT BAR OR AB STRAP TO THE

 

 

HIGH PULLEY STATION

 

47

 

 

Attach the Lat Bar (61) to the Ab Cable (47) with a

 

69

Cable Clip (69). For some exercises, the Chain (67)

 

 

 

should be attached between the Lat Bar and the Ab

 

 

Cable with two Cable Clips. Adjust the length of the

69

 

Chain between the Lat Bar and the Ab Cable so the

 

 

Lat Bar is in the correct starting position for the

61

 

exercise to be performed.

67

 

 

The Ab Strap (81) can be attached in the same manner.

 

81

ATTACHING THE LAT BAR, AB STRAP, OR NYLON

72

 

STRAP TO THE LOW PULLEY STATION

 

 

 

Attach the Lat Bar (61) to the Weight Cable (72) with a

69

 

 

69

Cable Clip (69). For some exercises, the Chain (67)

 

should be attached between the Lat Bar and the Weight

 

81

 

 

Cable with two Cable Clips. Adjust the length of the

 

 

Chain between the Lat Bar and the Weight Cable so

67

 

the Lat Bar is in the correct starting position for the

 

 

exercise to be performed.

 

 

The Ab Strap (81) or Nylon Strap (26) can be attached

26

61

 

 

 

in the same manner.

 

 

21

Image 21
Contents QUESTIONS? Model No. PFSY59001 Serial NoCustomer HOT Line Table of Contents Important Precautions Decal Before YOU BeginMake Assembly Easier AssemblyFrame Assembly Do not tighten the Nylon Locknuts 50 yet Do not tighten the Nylon Locknuts yet Tighten the Nylon Locknuts 50 used in steps Locate and open the parts bag labeled ARM AssemblyPage Cable Assembly Page Page Weight Cable is in the groove of the Pulley Page Page Page Cable Trap is oriented to hold the Cable in place Locate and open the parts bag labeled Seat Assembly Seat AssemblyPage Adjustments Changing the Weight SettingAttaching the LAT BAR or AB Strap to High Pulley Station Adjusting the Backrest Adjusting the Curl PADAttaching the AB Strap to the AB Pulley Station Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceLeg Press Cable Press Upright Ab Cable Cable DiagramsButterfly Cable Left ArmWeight Cable Cable ID Stack Low Pulley R0402A Part Identification CHART-Model No. PFSY59001X 4 Bolt X 5 1/2 Bolt X 6 Bolt 2 x 2 1/2 Inner Cap 2 Square Inner Cap Round Inner Cap Key No. Qty Description Part LIST-Model No. PFSY59001Exploded Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT