ProForm PFSY59001 user manual Locate and open the parts bag labeled Seat Assembly

Page 19

SEAT ASSEMBLY

50.Locate and open the parts bag labeled “SEAT ASSEMBLY.”

Attach a Seat (13) to the brackets on the Butterfly Seat Frame (14) using four 1/4” x 3/4” Bolts (49).

Repeat this step with the other Seat (not shown) and the Press Seat Frame (not shown).

51.Press a 1 1/2” Square Inner Cap (35) into the end of the Press Backrest Frame (44). Press four 3/4” Round Inner Caps (43) into the welded tubes on the Press Backrest Frame.

Attach a Backrest (12) to the Press Backrest Frame (44) with four 1/4” x 3/4” Bolts (49).

Pull out the Adjustment Knob (5) on the Press Upright (2) as far as it can go. Slide the Press Backrest Frame (44) into the Press Upright and snap the Adjustment Knob into a hole in the Press Backrest Frame. Turn the Adjustment Knob clock- wise until tight.

52.Press a 1 1/2” Square Inner Cap (35) into the end of the Butterfly Backrest Frame (70). Attach the other Backrest (12) to the Butterfly Backrest Frame with four 1/4” x 3/4” Bolts (49).

Pull out the Adjustment Knob (5) on the Butterfly Upright (1) as far as it can go. Slide the Butterfly Backrest Frame (70) into the Butterfly Upright and snap the Adjustment Knob into a hole in the Butterfly Backrest Frame. Turn the Adjustment Knob clockwise until tight.

53.See drawing A. Attach the Shroud (34) to the Press Top Frame (9) with two #8 x 1/2” Screws (45).

See drawing B. Attach the Shroud (34) to the Press Base (6) with two #8 x 1/2” Screws (45).

19

50

14

 

 

 

 

13

 

 

 

 

 

49

 

51

 

43

 

 

 

49

2

 

 

44

5

 

 

 

 

 

 

35

 

12

 

 

 

 

49

 

 

 

43

 

52

35

49

 

 

 

 

5

70

12

 

 

 

1

49

 

53

 

A

B

 

 

9

 

 

45

 

 

 

34

 

 

 

 

34

 

 

 

 

6

 

 

 

45

Image 19
Contents Model No. PFSY59001 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Decal Before YOU BeginMake Assembly Easier AssemblyFrame Assembly Do not tighten the Nylon Locknuts 50 yet Do not tighten the Nylon Locknuts yet Tighten the Nylon Locknuts 50 used in steps Locate and open the parts bag labeled ARM AssemblyPage Cable Assembly Page Page Weight Cable is in the groove of the Pulley Page Page Page Cable Trap is oriented to hold the Cable in place Locate and open the parts bag labeled Seat Assembly Seat AssemblyPage Changing the Weight Setting AdjustmentsAttaching the LAT BAR or AB Strap to High Pulley Station Adjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceLeft Arm Cable DiagramsLeg Press Cable Press Upright Ab Cable Butterfly CableWeight Cable Cable ID Stack Low Pulley R0402A Part Identification CHART-Model No. PFSY59001X 4 Bolt X 5 1/2 Bolt X 6 Bolt 2 x 2 1/2 Inner Cap 2 Square Inner Cap Round Inner Cap Key No. Qty Description Part LIST-Model No. PFSY59001Exploded Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT