ProForm PFSY59001 user manual Do not tighten the Nylon Locknuts yet

Page 8

8.See the inset drawing. Insert two Weight Inserts

(56)into each Weight (21).

Set the two Weight Bumpers (51) over the holes in the corner bar of the Press Base (6).

Slide the Weight Guides (15) through the Weight Bumpers (51) and into the holes in the Press Base

(6). Secure the Weight Guides to the Press Base with two 3/8” x 2 3/4” Bolts (89), four 3/8” Washers (48), and two 3/8” Nylon Locknuts (50).

Slide the Weights (21) onto the Weight Guides (15), stacking them on top of the Weight Bumpers (51).

Note: Make sure that the Weights are oriented so that the slots in the Weights are toward the front, as shown.

9.Press the Weight Tube Bumper (18) into the Weight Tube (17).

Slide the Top Weight (16) onto the Weight Guides (15), so that the Weight Tube (17) goes into the center holes in the Weights (21).

10.Press a 1 1/2” x 2 1/2” Inner Cap (83) into the end of the Press Top Frame (9).

Attach the Press Top Frame (9) and a Support Plate (94) to the Press Upright (2) with two 3/8” x

2 1/2” Bolts (87) and two 3/8” Nylon Locknuts (50).

Do not tighten the Nylon Locknuts yet.

Note: Be sure that the Weight Guides (15) are properly positioned in relation to the Press Top Frame (9), as shown in drawing 11 on the next page.

8

8

 

 

 

56

 

15

 

 

 

 

 

 

21

 

21

 

Slot

 

 

 

 

 

89

 

 

 

 

51

89

48

 

 

48

 

 

 

 

48

48

 

6

 

 

 

50

 

 

 

 

9

 

 

 

16

 

 

 

 

 

15

 

17

 

18

 

 

 

 

 

 

21

 

10

 

 

 

87

 

 

 

94

 

 

 

9

 

 

 

 

 

15

 

83

 

50

 

 

 

 

50

 

 

 

 

 

2

 

Image 8
Contents Customer HOT Line QUESTIONS?Model No. PFSY59001 Serial No Table of Contents Important Precautions Before YOU Begin DecalAssembly Make Assembly EasierFrame Assembly Do not tighten the Nylon Locknuts 50 yet Do not tighten the Nylon Locknuts yet Locate and open the parts bag labeled ARM Assembly Tighten the Nylon Locknuts 50 used in stepsPage Cable Assembly Page Page Weight Cable is in the groove of the Pulley Page Page Page Cable Trap is oriented to hold the Cable in place Seat Assembly Locate and open the parts bag labeled Seat AssemblyPage Attaching the LAT BAR or AB Strap to High Pulley Station AdjustmentsChanging the Weight Setting Attaching the AB Strap to the AB Pulley Station Adjusting the BackrestAdjusting the Curl PAD Weight Resistance Chart PlatesTROUBLE-SHOOTING and Maintenance Tightening the CablesCable Diagrams Leg Press Cable Press Upright Ab CableButterfly Cable Left ArmWeight Cable Cable ID Stack Low Pulley Part Identification CHART-Model No. PFSY59001 R0402AX 4 Bolt X 5 1/2 Bolt X 6 Bolt 2 x 2 1/2 Inner Cap 2 Square Inner Cap Round Inner Cap Part LIST-Model No. PFSY59001 Key No. Qty DescriptionExploded Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty