ProForm PFSY59001 user manual Do not tighten the Nylon Locknuts 50 yet

Page 7

4.Attach the Butterfly Seat Frame (14) to the Butterfly Upright (1) with two 3/8” x 3 3/4” Bolts (102), two 3/8” Washers (48), and two 3/8” Nylon Locknuts (50).

Attach the Butterfly Seat Frame (14) to the Butterfly Front Leg (3) with two 3/8” x 3 3/4” Bolts (102), two 3/8” Washers (48) and two 3/8” Nylon Locknuts (50).

Do not tighten the Nylon Locknuts (50) yet.

5.Press a 3” Round Inner Cap (78) into the Press Front Leg (20).

Attach the Press Front Leg (20) to the indicated 3/8” x 2” Carriage Bolts (92) on the Press Base (6) with two 3/8” Nylon Locknuts (50).Do not tighten the Nylon Locknuts yet. Make sure that the Press Front Leg is turned so that the indicated hole is on the side shown.

6.Attach the Press Seat Frame (7) to the Press Upright (2) with two 3/8” x 3 3/4” Bolts (102), the Rounded Support Plate (104), and two 3/8” Nylon Locknuts (50).

Attach the Press Seat Frame (7) to the Press Front Leg (20) with two 3/8” x 3 3/4” Bolts (102), two 3/8” Washers (48), and two 3/8” Nylon Locknuts (50).

Do not tighten the Nylon Locknuts (50) yet.

7.Insert three 1 1/2” x 2 1/2” Inner Caps (83) into the ends of the Butterfly Top Frame (33).

Attach the Butterfly Top Frame (33) to the Butterfly Upright (1) with two 3/8” x 2 1/2” Bolts (87), a Support Plate (94), and two 3/8” Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet.

7

4

 

50

 

 

 

 

102

1

 

 

 

 

 

50

48

50

14

 

 

 

50

 

 

 

 

48

 

 

3

 

 

 

 

102

5

78

 

 

 

 

 

Hole

 

 

 

20

50

 

 

 

 

 

50

 

 

 

 

 

6

 

 

92

 

6

 

50

 

 

 

 

 

7

 

104

 

50

 

 

 

 

102

 

 

50

 

 

50

 

 

 

 

 

2

48

 

 

 

 

20

 

 

102

 

 

 

48

 

 

7

 

33

87

 

 

 

 

 

 

83

 

83

 

 

94

 

 

 

 

 

83

 

 

50

 

 

 

1

50

Image 7
Contents Model No. PFSY59001 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Decal Before YOU BeginMake Assembly Easier AssemblyFrame Assembly Do not tighten the Nylon Locknuts 50 yet Do not tighten the Nylon Locknuts yet Tighten the Nylon Locknuts 50 used in steps Locate and open the parts bag labeled ARM AssemblyPage Cable Assembly Page Page Weight Cable is in the groove of the Pulley Page Page Page Cable Trap is oriented to hold the Cable in place Locate and open the parts bag labeled Seat Assembly Seat AssemblyPage Changing the Weight Setting AdjustmentsAttaching the LAT BAR or AB Strap to High Pulley Station Adjusting the Curl PAD Adjusting the BackrestAttaching the AB Strap to the AB Pulley Station Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceLeft Arm Cable DiagramsLeg Press Cable Press Upright Ab Cable Butterfly CableWeight Cable Cable ID Stack Low Pulley R0402A Part Identification CHART-Model No. PFSY59001X 4 Bolt X 5 1/2 Bolt X 6 Bolt 2 x 2 1/2 Inner Cap 2 Square Inner Cap Round Inner Cap Key No. Qty Description Part LIST-Model No. PFSY59001Exploded Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT