ProForm 705 ZLT manual Operation and Adjustment, PRE-LUBRICATED Walking Belt, Australia, Outlet

Page 16

OPERATION AND ADJUSTMENT

THE PRE-LUBRICATED WALKING BELT

Your treadmill features a walking belt coated with high- performance lubricant. IMPORTANT: Never apply sil- icone spray or other substances to the walking belt or the walking platform. Such substances will dete- riorate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

This product must be earthed. If it should malfunc- tion or break down, earthing provides a path of least resistance for electric current to reduce the risk of elec- tric shock. This product is equipped with a power cord having an equipment-earthing conductor and an earth- ing plug. IMPORTANT: If the power cord is dam- aged, it must be replaced with a manufacturer- recommended power cord.

DANGER: Improper connection of the equipment-earthing conductor can result in an increased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly earthed. Do not modify the plug pro- vided with the product—if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Follow the steps below to plug in the power cord.

1.Plug the indicated end of the power cord into the socket on the treadmill.

Socket on Treadmill

Power Cord

2.If you are plugging in the power cord in Australia, go to step 3.

If you are plugging in the power cord in the UK, first press the pins on the power cord into the metal clips in the adapter as shown. Close the adapter cover over the end of the power cord and tighten the screw in the adapter. IMPORTANT: Make sure that the screw is tightened into the adapter cover. Then, go to step 3.

Screw

Adapter

Cover

Adapter

Pins

Metal

 

Clips

3.Plug the power cord into an appropriate outlet that is properly installed and earthed in accordance with all local codes and ordinances.

UK

Australia

Outlet

Outlet

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents QUESTIONS? Model No. PETL79810.0 Serial NoTable of Contents Important Precautions Save These InstructionsBefore YOU Begin Assembly Repeat this step on the other side Treadmill Make sure that the power cord is unpluggedDo not fully fold the Frame yet Be careful not to pinch the Upright Wire See the inset drawing. Tie the wire tieFully tighten the Patch Bolts yet Page Patch Bolts yet Page Page Screws, and then tighten each of them Page HOW to USE the Chest Pulse Sensor HOW to PUT on the Chest Pulse SensorCare and Maintenance TroubleshootingOperation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt AustraliaFeatures of the Console DiagramConsole HOW to Turn on the Power HOW to USE the Manual ModeInsert the key into the console Start the walking beltFor several seconds, each time the incline changes Measure your heart rate if desired Select a preset workout HOW to USE a Preset WorkoutMonitor your progress with the matrix and the displays HOW to USE AN Ifit Workout Insert an iFit card and select a workoutInformation Mode HOW to USE the Stereo Sound SystemHOW to Fold and Move the Treadmill HOW to Fold the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopProblem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Part LIST-Model No. PETL79810.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. PETL79810.0 R0710A Exploded Drawing B-Model No. PETL79810.0 R0710A Exploded Drawing C-Model No. PETL79810.0 Exploded Drawing D-Model No. PETL79810.0 R0710A Ordering Replacement Parts Recycling Information
Top Page Image Contents