ProForm 705 ZLT manual HOW to Fold and Move the Treadmill, HOW to Fold the Treadmill

Page 24

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL

To avoid damaging the treadmill, adjust the incline to the lowest position before you fold the treadmill. Then, remove the key and unplug the power cord.

CAUTION: You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill.

1.Hold the metal frame firmly in the location shown by the arrow below. CAUTION: Do not hold the frame by the plastic foot rails. Bend your legs and keep your back straight.

1

Frame

2.Raise the frame until the latch knob locks in the storage position. CAUTION: Make sure that the latch knob locks.

2 Frame

Latch

Knob

To protect the floor or carpet, place a mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° F (30° C).

HOW TO MOVE THE TREADMILL

Before moving the treadmill, fold it as described at the left. CAUTION: Make sure that the latch knob is locked in the storage position. Moving the tread- mill may require two people.

1.Hold the frame and one of the handrails, and place one foot against a wheel.

1

Frame

Handrail

Wheel

2.Pull back on the handrail until the treadmill will roll on the wheels, and carefully move it to the desired location. CAUTION: Do not move the treadmill without tipping it back, do not pull on the frame, and do not move the treadmill over an uneven surface.

3.Place one foot against a wheel, and carefully lower the treadmill.

HOW TO LOWER THE TREADMILL FOR USE

1.See drawing 2. Hold the upper end of the treadmill frame with your right hand. Pull the latch knob to the left; if necessary, push the frame forward slightly. Pivot the frame downward a few inches, and release the latch knob.

2.See drawing 1 at the left. Hold the metal frame firmly with both hands, and lower it to the floor.

CAUTION: Do not hold the frame by the plastic foot rails, and do not drop the frame. Bend your legs and keep your back straight.

24

Image 24
Contents QUESTIONS? Model No. PETL79810.0 Serial NoTable of Contents Important Precautions Save These InstructionsBefore YOU Begin Assembly Make sure that the power cord is unplugged Repeat this step on the other side TreadmillDo not fully fold the Frame yet See the inset drawing. Tie the wire tie Be careful not to pinch the Upright WireFully tighten the Patch Bolts yet Page Patch Bolts yet Page Page Screws, and then tighten each of them Page HOW to USE the Chest Pulse Sensor HOW to PUT on the Chest Pulse SensorCare and Maintenance TroubleshootingOperation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt AustraliaDiagram Features of the ConsoleConsole HOW to Turn on the Power HOW to USE the Manual ModeInsert the key into the console Start the walking beltFor several seconds, each time the incline changes Measure your heart rate if desired HOW to USE a Preset Workout Select a preset workoutMonitor your progress with the matrix and the displays HOW to USE AN Ifit Workout Insert an iFit card and select a workoutInformation Mode HOW to USE the Stereo Sound SystemHOW to Fold and Move the Treadmill HOW to Fold the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopProblem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Part LIST-Model No. PETL79810.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. PETL79810.0 R0710A Exploded Drawing B-Model No. PETL79810.0 R0710A Exploded Drawing C-Model No. PETL79810.0 Exploded Drawing D-Model No. PETL79810.0 R0710A Ordering Replacement Parts Recycling Information