ResMed S9 VPAP Tx manual General warnings and cautions

Page 5

General warnings and cautions

WARNINGS

•• Read the entire manual before using the device.

•• Use the device only as directed by the physician or healthcare provider.

•• Use the device only for the intended use as described in this manual. Advice contained in this manual should not supersede instructions given by the physician.

•• If you notice any unexplained changes in the performance of the device, if it is making unusual or harsh sounds, if the device or the power supply are dropped or mishandled, if water is spilled into the enclosure, or if the enclosure is broken, discontinue use and contact your ResMed Service Center.

•• The device should only be used with masks (and connectors) recommended by ResMed or by a physician or respiratory therapist. A mask should not be used unless the device is turned on. Once the mask is fitted, ensure that the device is blowing air.The vent hole or holes associated with the mask should never be blocked.

Explanation:The device is intended to be used with special masks (or connectors) which have vent holes to allow continuous flow of air out of the mask. When the device is turned on and functioning properly, new air from the device flushes the exhaled air out through the mask vent holes. However, when the device is not operating, insufficient fresh air will be provided through the mask, and the exhaled air may be rebreathed. Rebreathing of exhaled air for longer than several minutes can, in some circumstances, lead to suffocation.This applies to most models of CPAP or bilevel devices

•• Only ResMed air tubing and accessories should be used with the device. A different type of air tubing or accessory may alter the pressure you actually receive, reducing the effectiveness of the treatment.

•• Only use the ResMed 90W or 30W power supply unit. Use the 90W power supply unit to power the system comprising the device, H5i, air tubing, DC/DC converter and battery pack.The 30W power supply unit is designed to power the device only and recommended for traveling.

•• To maintain electrical safety and in accordance with IEC 60601, where a personal computer is used with the flow generator, the personal computer must be at least 5’ (1.5 m) away from, or at least 8’ (2.5 m) above the patient.The Personal Computer must comply to IEC 60950.

CAUTIONS

•• In the US, Federal law restricts the device to sale by or on order of a physician.

•• Ensure that the device is protected against water. Enclose the device in the S9 travel bag for transport.

Note: The above are general warnings and cautions. Specific warnings, cautions and notes appear with the relevant instructions in the manual.

1 English

Image 5
Contents S9 Vpap Tx Page S9 Vpap Tx Contents General warnings and cautions S9 Vpap Tx indications for use WelcomeS9 Vpap Tx contraindications S9 Vpap Tx adverse effectsS9 Vpap Tx at a glance Supplemental oxygen MasksAntibacterial filters HumidifierTherapy modes Therapy mode DescriptionKey Function S9 Vpap Tx basicsSetting up the S9 Vpap Tx Filling the water tub English Air tubing Specifications Settings Mask and air tubing settingsMask type Settings Home menu Navigating the menusAbout the menus Humidity level Changing settings via the Home menuClimate Control Mask FitViewing the treatment screens Parameter Modes Description Treatment screen parametersSetup menu access Setup menuSettings ConfigurationParameter Modes Clinical setup menu parametersRange Description Ü ü ü ü ü ü ü üÜ ü ü Parameter Modes Range DescriptionLED Parameter Description ServiceInfo menu Managing Climate Control TemperatureMode Heated tubeDelivering therapy To add supplemental oxygen Adding supplemental oxygenFilter Efficiency Cleaning and maintenanceTesting the alarms Working with alarmsAlarms menu Problem/Possible cause Solution TroubleshootingNo display Insufficient air delivered from the deviceWater splashing on your face from the H5i Alarm is activated and the LCD screen display disappearsLeaking water tub Air feels too warm/cold in the maskS9 Vpap Tx technical specifications Technical specificationsGeneral technical specifications Pneumatic flow path Flow maximum at set pressures Value Range Display resolutionDisplayed values MinServicing SymbolsProduct Limited warrantyPage GLO Multi