JVC UX-A70MDR manual Connecting Other Equipment, To connect speakers

Page 12

Continued

To connect speakers

You can connect the speakers using the speaker cords.

1
2	Speaker terminals		3,4
		Red
Speaker cord	+	+	Speaker cord
	+	+
	R	L
	-	-
		Black
	R		L
Rear of the right		Rear of the left
speaker		speaker

1If cords are covered with insulation, twist the core of the cord at the end of each cord, then remove the insulation.

2Open the speaker terminal.

3Insert the end of the speaker cord to the terminal. Match the polarity of the speaker terminals: White (+) to red (+) and black (–) to black (–).

4Close the speaker terminal on the rear of the unit.

Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit.

Connecting Other Equipment

You can connect the following equipment which can be used as a playback and recording device. By using the cassette deck, for example, you can record any source played back on this unit.

When you connect and use the equipment, refer also to its manual supplied.

•DO NOT connect other equipment while the power is on.

•DO NOT plug in any equipment until all connections are complete.

To connect another component such as a cassette deck

Be sure that the plugs of the audio cords and the jacks on the rear of the unit are color-coded: White plugs and jacks are for left audio signals, and red ones for right audio signals.

To output (PLAY)

Ex. Cassette deck

To input (REC)

–

ANTENNA

AM EXT

AM LOOP

FM(75Ω)

COAXIAL

By using audio cords (not supplied), connect:

•Between the audio input jacks on the cassette deck and the LINE OUT jacks — For recording on the cassette deck.

•Between the audio output jacks on the cassette deck and the LINE IN jacks — For playing a tape.

– 8 –

Image 12

Contents UX-A70MDR If in Doubt Consult a Competent Electrician Class Laser Product Above ALL Precautions IntroductionContents Location of the Buttons Main unitBecome familiar with the buttons on your unit Main Unit Display windowRemote Control Remote ControlWhen using the remote control Connecting Antennas Getting StartedUnpacking FM antennaConnecting Speakers AM MW/LW antennaTo connect an outdoor AM MW/LW antenna To attach spacersConnecting Other Equipment You can connect the speakers using the speaker cordsTo connect speakers To connect another component such as a cassette deckPutting the Batteries into the Remote Control To stop and cancel the display demonstration, pressTo start the display demonstration manually, press Basic and Common Operations Turning On the Power AC power cord from the AC outletSelecting the Sources and Starting Play To turn on the unit without playing, pressAdjusting the Volume To turn down the volume level temporarilyReinforcing the Bass Sound Selecting the Sound ModesSetting the Display Illumination To set the illumination colorTo create your favorite colors To dim the display illuminationListening to FM and AM MW/LW Broadcasts Tuning in a Station Presetting StationsTo change the FM reception mode Tuning in a Preset Station Receiving FM Stations with RDSChanging the RDS Information Searching for Programs by PTY Codes PTY SearchSwitching to a Program Type of Your Choice Temporarily Alarm function Test functionMore about the EON function Description of the PTY codes Playing Back a CD Basic CD Operations To stop playback for a momentTo locate a particular point in a track during play To go to another trackTo check the program contents Program PlayTo modify the program On the remote control only Playing at Random Random PlayRepeating Tracks Repeat Play To skip the current track, press ¢Playing Back an MD You can play an MD On the main unit only Press MD OPEN/CLOSEInsert an MD into the MD loading slot Press MD #Basic MD Operations Programing the Playing Order of the Tracks Program PlayTo change the information in the main display Random play ends when all the tracks are played once On the remote control only Load an MD Press MD # / 8, thenTo skip the playing track, press ¢ Tracks of the loaded MD will play at randomMain unit Remote control Recording on MDBefore You Start Recording About the track marksTo avoid erasing important recordings To put a track mark manually while recording anPrecautions for performing long-hour stereo recording Stereo Long-Hour Recording MdlpAbout High-Speed Recording To check the remaining recording timeRecording FM/AM MW/LW Broadcasts Recording CD CD Synchronized RecordingPress REC Mode to select the recording mode To record a single track during play or pausePress AUX Start playback on the external equipmentEditing MD Introducing MD Editing Functions Divide Function Join FunctionMove Function + 1 ? appears in the main displayTo divide the joined tracks, see the Divide function Select the track you want to move Press ¢orErase Function ALL Erase FunctionSelect the track you want to erase Press ¢ or Press SET Repeat to select all the tracks you want to eraseAssigning Titles to an MD Press ¯or ¿to change the title entry mode Press SET to enter the selected title entry modeDisc title entry screen appears when you press Track title entry screen appears when you pressChanging the Title Using the Timers Setting the Clock Using Recording TimerHow Recording Timer actually works Using Daily Timer How Daily Timer actually worksTo turn on the Recording Timer, press SET Press ¢or 4 repeatedly to adjust the minute Press SET Volume setting appears in the main displayTo turn on the Daily Timer, press SET If the unit is kept turned on when the timer-on time comesUsing Sleep Timer Timer PriorityHow Sleep Timer actually works Maintenance Cleaning the unitGeneral Notes Handling CDsUtoc User Table Of Contents Additional InformationMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Scms Serial Copy Management System Hcms High-speed Copy Management SystemMD Messages Malfunction has occurred duringMD is not loaded correctly There is no MD Troubleshooting SpecificationsJVC 1100TMMMDWJEM