JVC UX-A70MDR manual Adjusting the Volume, Reinforcing the Bass Sound, Selecting the Sound Modes

Page 16

Adjusting the Volume

You can adjust the volume level only while the unit is turned on.

To decrease the volume, press VOLUME – .To increase the volume, press VOLUME + .

(VOL. 40)

(VOL. 0)

•When press and hold each button, you can change the volume level continuously.

Reinforcing the Bass Sound

The richness and fullness of the bass sound is clearly maintained regardless of how low you set the volume — Active Hyper Bass PRO.

• You can use this effect only for playback.

To get the effect, press AHB PRO.

“BASS ON” appears in the main display and the BASS indicator lights on the display.

To cancel the effect, press AHB PRO again.

“BASS OFF” appears in the main display and the BASS indicator goes off from the display.

For private listening

Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on the headphones.

If “CAN NOT LISTEN” appears in the main display

During high-speed recording (see page 30), you cannot listen to any source, and therefore, cannot adjust the volume level.

DO NOT turn off (on standby) the unit with the volume set to an extremely high level; otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source.

REMEMBER you cannot adjust the volume level while the unit is in standby mode.

To turn down the volume level temporarily

On the remote control ONLY:

Press FADE MUTING.

The unit automatically decreases the volume level to “VOL.MIN” at once.

To restore the sound, press FADE MUTING again.

Selecting the Sound Modes

You can select one of the 3 preset sound modes. The sound modes can be applied only to playback sounds, and cannot be used for recording.

On the remote control ONLY:

To select the sound modes, press SOUND MODE repeatedly until the sound mode you want appears in the main display.

The SOUND indicator also lights on the display.

•Each time you press the button, the sound mode changes as follows:

FLAT ROCK POP CLASSIC

(Canceled)

ROCK:Boosts low and high frequency. Good for acoustic music.

POP:Good for vocal music or voice.

CLASSIC: Good for classical music.

FLAT:Cancels the sound mode.

To check the sound mode currently selected, press SOUND MODE once while the SOUND indicator is lit. The currently selected sound mode will appear in the main display.

– 12 –

Page 15 Page 17
Image 16
Page 15 Page 17
Contents UX-A70MDR If in Doubt Consult a Competent Electrician Class Laser Product Above ALL Precautions IntroductionContents Main unit Location of the ButtonsBecome familiar with the buttons on your unit Main Unit Display windowRemote Control Remote ControlWhen using the remote control Connecting Antennas Getting StartedUnpacking FM antennaConnecting Speakers AM MW/LW antennaTo connect an outdoor AM MW/LW antenna To attach spacersConnecting Other Equipment You can connect the speakers using the speaker cordsTo connect speakers To connect another component such as a cassette deckTo stop and cancel the display demonstration, press Putting the Batteries into the Remote ControlTo start the display demonstration manually, press Basic and Common Operations Turning On the Power AC power cord from the AC outletSelecting the Sources and Starting Play To turn on the unit without playing, pressAdjusting the Volume To turn down the volume level temporarilyReinforcing the Bass Sound Selecting the Sound ModesSetting the Display Illumination To set the illumination colorTo create your favorite colors To dim the display illuminationListening to FM and AM MW/LW Broadcasts Presetting Stations Tuning in a StationTo change the FM reception mode Tuning in a Preset Station Receiving FM Stations with RDSChanging the RDS Information Searching for Programs by PTY Codes PTY SearchSwitching to a Program Type of Your Choice Temporarily Test function Alarm functionMore about the EON function Description of the PTY codes Playing Back a CD Basic CD Operations To stop playback for a momentTo locate a particular point in a track during play To go to another trackProgram Play To check the program contentsTo modify the program On the remote control only Playing at Random Random PlayRepeating Tracks Repeat Play To skip the current track, press ¢Playing Back an MD You can play an MD On the main unit only Press MD OPEN/CLOSEInsert an MD into the MD loading slot Press MD #Programing the Playing Order of the Tracks Program Play Basic MD OperationsTo change the information in the main display Random play ends when all the tracks are played once On the remote control only Load an MD Press MD # / 8, thenTo skip the playing track, press ¢ Tracks of the loaded MD will play at randomMain unit Remote control Recording on MDBefore You Start Recording About the track marksTo avoid erasing important recordings To put a track mark manually while recording anPrecautions for performing long-hour stereo recording Stereo Long-Hour Recording MdlpAbout High-Speed Recording To check the remaining recording timeRecording FM/AM MW/LW Broadcasts Recording CD CD Synchronized RecordingPress REC Mode to select the recording mode To record a single track during play or pausePress AUX Start playback on the external equipmentEditing MD Introducing MD Editing Functions Divide Function Join FunctionMove Function + 1 ? appears in the main displayTo divide the joined tracks, see the Divide function Select the track you want to move Press ¢orErase Function ALL Erase FunctionSelect the track you want to erase Press ¢ or Press SET Repeat to select all the tracks you want to eraseAssigning Titles to an MD Press ¯or ¿to change the title entry mode Press SET to enter the selected title entry modeDisc title entry screen appears when you press Track title entry screen appears when you pressChanging the Title Using the Timers Using Recording Timer Setting the ClockHow Recording Timer actually works How Daily Timer actually works Using Daily TimerTo turn on the Recording Timer, press SET Press ¢or 4 repeatedly to adjust the minute Press SET Volume setting appears in the main displayTo turn on the Daily Timer, press SET If the unit is kept turned on when the timer-on time comesTimer Priority Using Sleep TimerHow Sleep Timer actually works Maintenance Cleaning the unitGeneral Notes Handling CDsUtoc User Table Of Contents Additional InformationMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Scms Serial Copy Management System Hcms High-speed Copy Management SystemMalfunction has occurred during MD MessagesMD is not loaded correctly There is no MD Troubleshooting SpecificationsJVC 1100TMMMDWJEM
Top Page Image Contents