JVC UX-A70MDR manual Tuning in a Station, Presetting Stations, To change the FM reception mode

Page 19

Tuning in a Station

1 Press FM/AM.

The unit automatically turns on and tunes in the previously tuned station (either FM or AM–MW/LW.)

•Each time you press the button, the band alternates between FM and AM (MW/LW.)

2 Press and hold ¢or 4until the station frequencies start changing continuously in the main display.

•¢: to increase the frequencies.

•4: to decrease the frequencies.

The unit starts searching stations and stops when a station of sufficient signal strength is tuned in.

Ex. An FM station is tuned in.

•If an FM program is broadcast in stereo, the STEREO indicator lights on the display.

To stop during searching, press ¢or 4.

When you repeatedly press ¢or 4

The frequency changes step by step.

To change the FM reception mode

When an FM stereo broadcast is noisy or hard to receive, you can change the FM reception mode to improve the reception.

On the remote control ONLY:

Press FM MODE.

•Each time you press the button, FM reception mode alternates between “STEREO” and “MONO.”

STEREO : Normally select this.

In this mode, you can hear stereo sound when a program is broadcast in stereo. In addition, static noise between stations will be erased while tuning.

MONO : Select this when an FM stereo broadcast is noisy or hard to receive. Reception improves though stereo effect is lost. The MONO indicator lights on the display.

Presetting Stations

You can preset 30 FM and 15 AM (MW/LW) stations manually.

In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the remote control ONLY:

1 Tune in the station (either FM or AM–MW/LW) you want to preset.

• See “Tuning in a Station” to the left.

2 Press SET.

The preset number starts flashing as follows:

•When you select an FM station in step 1

•When you select an AM (MW/LW) station in step 1

•The unit always starts from the preset number 1.

3 Press the number buttons to select a preset number.

Ex. For preset number 5, press 5.

For preset number 15, press +10, then 5. For preset number 20, press +10, then 10.

For preset number 30, press +10, +10, then 10.

•You can also select the preset number by pressing

¢or 4.

4 Press SET again.

“STORED” appears in the main display for a while.

The tuned station in step 1 is stored in the preset number selected in step 3.

•Storing a new station on a used number erases the previously stored one.

When you unplug the AC power cord or if a power failure occurs

The FM and AM (MW/LW) preset stations will be erased. If this happens, preset the stations again.

– 15 –

Page 18 Page 20
Image 19
Page 18 Page 20
Contents UX-A70MDR If in Doubt Consult a Competent Electrician Class Laser Product Above ALL Introduction PrecautionsContents Main unit Location of the ButtonsBecome familiar with the buttons on your unit Display window Main UnitRemote Control Remote ControlWhen using the remote control FM antenna Connecting AntennasGetting Started UnpackingTo attach spacers Connecting SpeakersAM MW/LW antenna To connect an outdoor AM MW/LW antennaTo connect another component such as a cassette deck Connecting Other EquipmentYou can connect the speakers using the speaker cords To connect speakersTo stop and cancel the display demonstration, press Putting the Batteries into the Remote ControlTo start the display demonstration manually, press Basic and Common Operations To turn on the unit without playing, press Turning On the PowerAC power cord from the AC outlet Selecting the Sources and Starting PlaySelecting the Sound Modes Adjusting the VolumeTo turn down the volume level temporarily Reinforcing the Bass SoundTo dim the display illumination Setting the Display IlluminationTo set the illumination color To create your favorite colorsListening to FM and AM MW/LW Broadcasts Presetting Stations Tuning in a StationTo change the FM reception mode Searching for Programs by PTY Codes PTY Search Tuning in a Preset StationReceiving FM Stations with RDS Changing the RDS InformationSwitching to a Program Type of Your Choice Temporarily Test function Alarm functionMore about the EON function Description of the PTY codes Playing Back a CD To go to another track Basic CD OperationsTo stop playback for a moment To locate a particular point in a track during playProgram Play To check the program contentsTo modify the program To skip the current track, press ¢ On the remote control onlyPlaying at Random Random Play Repeating Tracks Repeat PlayPlaying Back an MD Press MD # You can play an MDOn the main unit only Press MD OPEN/CLOSE Insert an MD into the MD loading slotPrograming the Playing Order of the Tracks Program Play Basic MD OperationsTo change the information in the main display Tracks of the loaded MD will play at random Random play ends when all the tracks are played onceOn the remote control only Load an MD Press MD # / 8, then To skip the playing track, press ¢Recording on MD Main unit Remote controlTo put a track mark manually while recording an Before You Start RecordingAbout the track marks To avoid erasing important recordingsTo check the remaining recording time Precautions for performing long-hour stereo recordingStereo Long-Hour Recording Mdlp About High-Speed RecordingRecording CD CD Synchronized Recording Recording FM/AM MW/LW BroadcastsStart playback on the external equipment Press REC Mode to select the recording modeTo record a single track during play or pause Press AUXEditing MD Introducing MD Editing Functions Join Function Divide FunctionSelect the track you want to move Press ¢or Move Function+ 1 ? appears in the main display To divide the joined tracks, see the Divide functionPress SET Repeat to select all the tracks you want to erase Erase FunctionALL Erase Function Select the track you want to erase Press ¢ orAssigning Titles to an MD Track title entry screen appears when you press Press ¯or ¿to change the title entry modePress SET to enter the selected title entry mode Disc title entry screen appears when you pressChanging the Title Using the Timers Using Recording Timer Setting the ClockHow Recording Timer actually works How Daily Timer actually works Using Daily TimerTo turn on the Recording Timer, press SET If the unit is kept turned on when the timer-on time comes Press ¢or 4 repeatedly to adjust the minute Press SETVolume setting appears in the main display To turn on the Daily Timer, press SETTimer Priority Using Sleep TimerHow Sleep Timer actually works Handling CDs MaintenanceCleaning the unit General NotesAtrac Adaptive TRansform Acoustic Coding/ATRAC3 Utoc User Table Of ContentsAdditional Information MD Disc TypesHcms High-speed Copy Management System Scms Serial Copy Management SystemMalfunction has occurred during MD MessagesMD is not loaded correctly There is no MD Specifications TroubleshootingJVC 1100TMMMDWJEM
Top Page Image Contents