JVC UX-A70MDR Connecting Speakers, To connect an outdoor AM MW/LW antenna, To attach spacers

Page 11

AM (MW/LW) antenna

1
2	Vinyl-covered wire
2	(not supplied)
3
AM (MW/LW) loop antenna
(supplied)

1If cords are covered with insulation, twist the core of the cord at the end of each cord, then remove the insulation.

2Connect the AM (MW/LW) loop antenna to the AM LOOP terminals as illustrated.

3Turn the AM (MW/LW) loop antenna until you have the best reception.

To connect an outdoor AM (MW/LW) antenna

When reception is poor, connect a single vinyl-covered wire to the AM EXT terminal and extend it horizontally. The AM (MW/LW) loop antenna must remain connected.

For better reception of both FM and AM (MW/LW)

•Make sure the antenna conductors do not touch any other terminals and connecting cords.

•Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord.

Connecting Speakers

To attach spacers

If you want to put the speakers on the side of the main unit, you need to make a space between the main unit and the right speaker for ventilation.

In this case, attach spacers (supplied) to the right speaker as the illustration below:

The main unit

The right speaker

The openings for ventilation

Spacers (supplied)

By peeling the cover seal from spacers, you can attach them to the right speaker.

To remove the speaker grilles

The speaker grilles are removable as the illustration below:

HolesProjections

Speaker grille

To remove the speaker grille, insert your fingers at the top of the speaker grille, then pull towards you. Also pull the bottom towards you.

To attach the speaker grille, put the projections of the speaker grille into the holes of the speaker.

– 7 –

Image 11

Contents UX-A70MDR If in Doubt Consult a Competent Electrician Class Laser Product Above ALL Introduction PrecautionsContents Become familiar with the buttons on your unit Location of the ButtonsMain unit Display window Main UnitWhen using the remote control Remote ControlRemote Control FM antenna Connecting AntennasGetting Started UnpackingTo attach spacers Connecting SpeakersAM MW/LW antenna To connect an outdoor AM MW/LW antennaTo connect another component such as a cassette deck Connecting Other EquipmentYou can connect the speakers using the speaker cords To connect speakersTo start the display demonstration manually, press Putting the Batteries into the Remote ControlTo stop and cancel the display demonstration, press Basic and Common Operations To turn on the unit without playing, press Turning On the PowerAC power cord from the AC outlet Selecting the Sources and Starting PlaySelecting the Sound Modes Adjusting the VolumeTo turn down the volume level temporarily Reinforcing the Bass SoundTo dim the display illumination Setting the Display IlluminationTo set the illumination color To create your favorite colorsListening to FM and AM MW/LW Broadcasts To change the FM reception mode Tuning in a StationPresetting Stations Searching for Programs by PTY Codes PTY Search Tuning in a Preset StationReceiving FM Stations with RDS Changing the RDS InformationSwitching to a Program Type of Your Choice Temporarily More about the EON function Alarm functionTest function Description of the PTY codes Playing Back a CD To go to another track Basic CD OperationsTo stop playback for a moment To locate a particular point in a track during playTo modify the program To check the program contentsProgram Play To skip the current track, press ¢ On the remote control onlyPlaying at Random Random Play Repeating Tracks Repeat PlayPlaying Back an MD Press MD # You can play an MDOn the main unit only Press MD OPEN/CLOSE Insert an MD into the MD loading slotTo change the information in the main display Basic MD OperationsPrograming the Playing Order of the Tracks Program Play Tracks of the loaded MD will play at random Random play ends when all the tracks are played onceOn the remote control only Load an MD Press MD # / 8, then To skip the playing track, press ¢Recording on MD Main unit Remote controlTo put a track mark manually while recording an Before You Start RecordingAbout the track marks To avoid erasing important recordingsTo check the remaining recording time Precautions for performing long-hour stereo recordingStereo Long-Hour Recording Mdlp About High-Speed RecordingRecording CD CD Synchronized Recording Recording FM/AM MW/LW BroadcastsStart playback on the external equipment Press REC Mode to select the recording modeTo record a single track during play or pause Press AUXEditing MD Introducing MD Editing Functions Join Function Divide FunctionSelect the track you want to move Press ¢or Move Function+ 1 ? appears in the main display To divide the joined tracks, see the Divide functionPress SET Repeat to select all the tracks you want to erase Erase FunctionALL Erase Function Select the track you want to erase Press ¢ orAssigning Titles to an MD Track title entry screen appears when you press Press ¯or ¿to change the title entry modePress SET to enter the selected title entry mode Disc title entry screen appears when you pressChanging the Title Using the Timers How Recording Timer actually works Setting the ClockUsing Recording Timer To turn on the Recording Timer, press SET Using Daily TimerHow Daily Timer actually works If the unit is kept turned on when the timer-on time comes Press ¢or 4 repeatedly to adjust the minute Press SETVolume setting appears in the main display To turn on the Daily Timer, press SETHow Sleep Timer actually works Using Sleep TimerTimer Priority Handling CDs MaintenanceCleaning the unit General NotesAtrac Adaptive TRansform Acoustic Coding/ATRAC3 Utoc User Table Of ContentsAdditional Information MD Disc TypesHcms High-speed Copy Management System Scms Serial Copy Management SystemMD is not loaded correctly There is no MD MD MessagesMalfunction has occurred during Specifications TroubleshootingJVC 1100TMMMDWJEM