JVC UX-A70MDR manual Setting the Display Illumination, To set the illumination color

Page 17

Setting the Display Illumination

You can change the illumination color and brightness of the electronic swing panel and display window.

To set the illumination color

You can select the illumination color by your preference.

1 Press to turn on the unit.

2 Press COLOR repeatedly until the color you want appears in the main display.

•Each time you press the button, the illumination color changes as follows:

*

(blue)(light blue)

**

 

 

 

 

 

(green)

 

 

**

 

 

 

 

 

 

 

 

 

 

 

 

 

(yellow)

 

 

 

 

 

 

 

(white)

 

 

 

(orange)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(purple)

 

(pink)

 

(red)

 

 

Ex. Both “M1” and “M2” are set to “R0 G1 B1” at the shipment (see also the right column.)

*If you select “RANDOM,” the unit will select one from 9 preset colors at random as the illumination color every two seconds automatically.

**If you select “M1” or “M2,” you can use a custom color. See “To create your favorite colors” to the right.

More on the display color

•The colors shown in the display cannot always be reproduced precisely. Due to the circumstances (room temperature, etc.) where the unit is used, colors may vary slightly.

•When you change the color of the display, the display may seem to move back and forth; this is a characteristic of this unit and is not a malfunction.

•When a strong light strikes the display, the display happens to become dark, but this is not a malfunction.

To create your favorite colors

You can create two favorite colors and store them in memory as “M1” and “M2.”

On the remote control ONLY:

1 Press to turn on the unit.

2 Press COLOR repeatedly until “M1” or “M2” appears in the main display.

The value of “R (red)” starts flashing.

Ex.“M1” is selected. “M1” is already set to “R (red) 0 G (green) 1 B (blue) 1.”

3 To adjust the brightness of each color

1)Press ¯and ¿to select the color you want to adjust.

2)Press ¢or 4repeatedly to adjust the value of the brightness (between 0 – 6.)

•As you increase the number, the color becomes brighter.

3)Repeat steps 3 –1) and3 –2) to find your favorite color.

4 Press SET while flashing.

“MEMORY” appears in the main display and the setting is finished.

•Even if you do not press SET, the unit will finish the color setting mode automatically.

To dim the display illumination

To dim the brightness, press DIMMER.

•When you press DIMMER while the illumination color is set to “M1” or “M2,” the illumination color is changed to light blue.

To resume the brightness, press DIMMER again.

– 13 –

Page 16 Page 18
Image 17
Page 16 Page 18
Contents UX-A70MDR If in Doubt Consult a Competent Electrician Class Laser Product Above ALL Introduction PrecautionsContents Become familiar with the buttons on your unit Location of the ButtonsMain unit Display window Main UnitWhen using the remote control Remote ControlRemote Control Getting Started Connecting AntennasUnpacking FM antennaAM MW/LW antenna Connecting SpeakersTo connect an outdoor AM MW/LW antenna To attach spacersYou can connect the speakers using the speaker cords Connecting Other EquipmentTo connect speakers To connect another component such as a cassette deckTo start the display demonstration manually, press Putting the Batteries into the Remote ControlTo stop and cancel the display demonstration, press Basic and Common Operations AC power cord from the AC outlet Turning On the PowerSelecting the Sources and Starting Play To turn on the unit without playing, pressTo turn down the volume level temporarily Adjusting the VolumeReinforcing the Bass Sound Selecting the Sound ModesTo set the illumination color Setting the Display IlluminationTo create your favorite colors To dim the display illuminationListening to FM and AM MW/LW Broadcasts To change the FM reception mode Tuning in a StationPresetting Stations Receiving FM Stations with RDS Tuning in a Preset StationChanging the RDS Information Searching for Programs by PTY Codes PTY SearchSwitching to a Program Type of Your Choice Temporarily More about the EON function Alarm functionTest function Description of the PTY codes Playing Back a CD To stop playback for a moment Basic CD OperationsTo locate a particular point in a track during play To go to another trackTo modify the program To check the program contentsProgram Play Playing at Random Random Play On the remote control onlyRepeating Tracks Repeat Play To skip the current track, press ¢Playing Back an MD On the main unit only Press MD OPEN/CLOSE You can play an MDInsert an MD into the MD loading slot Press MD #To change the information in the main display Basic MD OperationsPrograming the Playing Order of the Tracks Program Play On the remote control only Load an MD Press MD # / 8, then Random play ends when all the tracks are played onceTo skip the playing track, press ¢ Tracks of the loaded MD will play at randomRecording on MD Main unit Remote controlAbout the track marks Before You Start RecordingTo avoid erasing important recordings To put a track mark manually while recording anStereo Long-Hour Recording Mdlp Precautions for performing long-hour stereo recordingAbout High-Speed Recording To check the remaining recording timeRecording CD CD Synchronized Recording Recording FM/AM MW/LW BroadcastsTo record a single track during play or pause Press REC Mode to select the recording modePress AUX Start playback on the external equipmentEditing MD Introducing MD Editing Functions Join Function Divide Function+ 1 ? appears in the main display Move FunctionTo divide the joined tracks, see the Divide function Select the track you want to move Press ¢orALL Erase Function Erase FunctionSelect the track you want to erase Press ¢ or Press SET Repeat to select all the tracks you want to eraseAssigning Titles to an MD Press SET to enter the selected title entry mode Press ¯or ¿to change the title entry modeDisc title entry screen appears when you press Track title entry screen appears when you pressChanging the Title Using the Timers How Recording Timer actually works Setting the ClockUsing Recording Timer To turn on the Recording Timer, press SET Using Daily TimerHow Daily Timer actually works Volume setting appears in the main display Press ¢or 4 repeatedly to adjust the minute Press SETTo turn on the Daily Timer, press SET If the unit is kept turned on when the timer-on time comesHow Sleep Timer actually works Using Sleep TimerTimer Priority Cleaning the unit MaintenanceGeneral Notes Handling CDsAdditional Information Utoc User Table Of ContentsMD Disc Types Atrac Adaptive TRansform Acoustic Coding/ATRAC3Hcms High-speed Copy Management System Scms Serial Copy Management SystemMD is not loaded correctly There is no MD MD MessagesMalfunction has occurred during Specifications TroubleshootingJVC 1100TMMMDWJEM
Top Page Image Contents